DSE DSEGenset Series Manuale di istruzioni per l'installazione - Pagina 2

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Controllore DSE DSEGenset Series. DSE DSEGenset Series 6.

Stampa la pagina

NOTE: Depending upon module configuration, some parameters in the Main and Running Editors may not

be available. For more information refer to DSE publication 057-322 DSE8600 Configuration Suite PC Software

Manual available from www.deepseaelectronics.com

MAIN CONFIGURATION EDITOR PARAMETERS

Section

Parameter As Shown On Display

Display

Contrast

Language

Current Date and Time

Alt Config

Default Config

Engine

Oil Pressure Low Shutdown

Oil Pressure Low Pre Alarm

Coolant Temperature Low Warning

Coolant Temp High Pre Alarm

Coolant Temp High Shutdown

Start Delay Off Load

Start Delay On Load

Start Delay Mains Fail

Start Delay Telemetry

Pre Heat Temp

Pre Heat Timer

Post Heat Temp

Post Heat Timer

Cranking

Cranking Rest

Safety On Delay

Smoke Limiting

Smoke Limiting Off

Warming

Cooling

Under Speed Shutdown

Under Speed Warning

Over Speed Warning

Over Speed Shutdown

Overspeed Overshoot

Fail To Stop Delay

Battery Under Voltage Warning

Battery Under Voltage Warning Delay

Battery Under Voltage Warning

Battery Over Voltage Warning

Battery Over Voltage Warning Delay

Battery Over Voltage Warning

Charge Alternator Failure Warning

Charge Alternator Warning Delay

Charge Alternator Failure Shutdown

Charge Alternator Shutdown Delay

Droop (CAN Engine Only)

Fuel Usage Running Rate

Fuel Usage Stopped Rate

DPF Auto Regen Inhibit

Specific Gravity

CAN Termination (CAN Engine Only)

Values

English, Other.

DD:MM:YY, hh:mm:ss

Default Config / Alternative Config

0.00 bar

0 ºC

0 h 0 m 0 s

0 ºC

0 h 0 m 0 s

0 ºC

0 h 0 m 0 s

0 m 0 s

0 h 0 m 0 s

Active / Inactive

0 RPM

Active / Inactive

0 RPM

Active / Inactive

0 RPM

0 m 0 s

0 %

0 m 0 s

Active / Inactive

0 h 0 m 0 s

0.0 V

Active / Inactive

0 h 0 m 0 s

0.0 V

Active / Inactive

0.0 V

0 h 0 m 0 s

Active / Inactive

0.0 V

0 h 0 m 0 s

Active / Inactive

0 %

Active / Inactive

0.80 to 1.00

Active / Inactive

MAIN CONFIGURATION EDITOR PARAMETERS (CONTINUED)

Section

Parameter As Shown On Display

Generator

Under Voltage Shutdown

Under Voltage Pre-Alarm

Loading Voltage

Nominal Voltage

Over Voltage Pre-Alarm

Over Voltage Shutdown

Under Frequency Shutdown

Under Frequency Pre-Alarm

Loading Frequency

Nominal frequency

Over Frequency Pre-Alarm

Over Frequency Shutdown

Full Load Rating

kW Overload Trip

Delayed Over Current

Gen Over Current Trip

AC System

CT Primary

CT Secondary

Short Circuit Trip

Earth CT Primary

Earth Fault Trip

Transient Delay

Gen Reverse Power Delay

Full kW Rating

Full kvar Rating

Ramp Up Rate

Ramp Down Rate

Load Level For More Sets

Load Level For Less Sets

Load Demand Priority

Gen Reverse Power Trip

Insufficient Capacity Delay

Insufficient Capacity Action

Reactive Load Control Mode

Load Parallel Power

Load Power Factor

Gen Over Zero Seq Volt

Gen Under Pos Seq Volt

Gen Over Neg Seq Volt

Gen Asymmetry High

Mains

Under Voltage Trip

Over Voltage Trip

Under Frequency Trip

Over Frequency Trip

Transient Delay

CT Primary

CT Secondary

Full kW Rating

Full kvar Rating

Mains Over Zero Seq Volt

Values

0 V

0.0 Hz

0 A

0 %

Active / Inactive

0 %

3 Phase, 4 Wire

0 A

Power Cycle After Exit

0 A

Power Cycle After Exit

0 %

0 A

Active / Inactive

0 %

0.0 s

0 kW

0 kvar

0 %

0 kW

0 m 0 s

None / Indication / Warning / Shutdown /

Electrical Trip

None / VAr Share / VAr Fixed Export

0 kW

In Mains Parallel Mode

0 %

In Mains Parallel Mode

Active / Inactive

0.0 V

Active / Inactive

0.0 V

Active / Inactive

0.0 V

Active / Inactive

0.0 V

0 V

0 Hz

0.0 s

0 A

Power Cycle After Exit

0 A

Power Cycle After Exit

0 kW

0 kvar

Active / Inactive

0 V