DSE DSEGenset Series Manuale di istruzioni per l'installazione - Pagina 4

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Controllore DSE DSEGenset Series. DSE DSEGenset Series 6.

ELECTRICAL SPECIFICATIONS

Parameter
DC Supply Voltage
Maximum Operating Current
Maximum Standby Current
Typical Power
(Controller On, Heater Off)
Typical Power
(Controller On, Heater On)
Mains Phase to Neutral Voltage Sensing
Mains Phase to Phase Voltage Sensing
Mains Voltage Sensing Offset from Earth
Volt-Free Output Rating

REQUIREMENTS FOR UL CERTIFICATION

WARNING!: More than one live circuit exists, see diagram overleaf for further information.
Specification
Description
Screw Terminal Tightening
• 4.5 lb-in (0.5 Nm)
Torque
• Terminals suitable for connection of conductor size 13 AWG to 20 AWG (0.5 mm² to
Conductors
2.5 mm²).
• Conductor protection must be provided in accordance with NFPA 70, Article 240
(USA)
• Low voltage circuits (35 V or less) must be supplied from the engine starting battery
or an isolated secondary circuit.
• The communication, sensor, and/or battery derived circuit conductors shall be
separated and secured to maintain at least ¼" (6 mm) separation from the generator
and mains connected circuit conductors unless all conductors are rated 600 V or
greater.
• Must be connected through UL Listed (if working to UL requirements) or recognized
Current Inputs
isolating current transformers with the secondary rating of 5 A max.
• Must be connected to communication circuits of UL Listed equipment (if working to
Communication Circuits
UL requirements)
• 0.5 A
DC Output Pilot Duty
• Suitable for flat surface mounting in Type 1 Enclosure Type rating with surrounding
Mounting
air temperature -22 ºF to +122 ºF (-30 ºC to +50 ºC)
• Suitable for pollution degree 3 environments when voltage sensing inputs do not
exceed 300 V. When used to monitor voltages over 300 V device to be installed in
an unventilated or filtered ventilation enclosure to maintain a pollution degree 2
environment.
Maximum Operating
• 122 ºF (50 ºC)
Temperature
Specification
8 V
to 35 V
DC
DC
530 mA at 12 V
280 mA at 24 V
320 mA at 12 V
120 mA at 24 V
3.8 W to 4.1 W
6.8 W to 7.1 W
15 V
to 345 V
AC
AC
26 V
to 720 V
AC
AC
100 V
AC
8 A at 250 V
5 A at 30 V
AC,
DC

DIMENSIONS AND MOUNTING

Parameter
Specification
248 mm x 182.6 mm x 45.2 mm (9.76 " x 7.18 " x 1.77 ")
Dimensions
220 mm X 160 mm (8.7" X 6.3")
Panel Cutout
Weight
0.76 kg (1.67 lb)
Operating Temperature with Standard
-30 ºC to +70 ºC (-22 ºF to +158 ºF)
Display
Operating Temperature with Heated
-40 ºC to +70 ºC (-40 ºF to +158 ºF)
Display
Storage Temperature
-40 ºC to +80 ºC (-40 ºF to +176 ºF)

FIXING CLIPS

NOTE: In conditions of excessive vibration, mount the control panel on suitable anti-vibration
mountings
The module is held into the control panel fascia using the supplied fixing clips.
Withdraw the fixing clip screw (turn anticlockwise) until only the pointed end is protruding from the clip.
Insert the three 'prongs' of the fixing clip into the slots in the side of the DSE module's case.
Pull the fixing clip backwards (towards the back of the module) ensuring all three prongs of the clip are
inside their allotted slots.
Turn the fixing clip screws clockwise until they make contact with the panel fascia.
Turn the screws a quarter of a turn to secure the module into the control panel's fascia. Care must be
taken not to over tighten the fixing clip screws.