Auber Instruments AT210 Manuale di istruzioni - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per Termometro Auber Instruments AT210. Auber Instruments AT210 3. Digital
Anche per Auber Instruments AT210: Note sull'uso (2 pagine), Manuale di istruzioni (3 pagine), Manuale di istruzioni (4 pagine)

Stampa la pagina

AUBER INSTRUMENTS

9. Peak value setting (code 0037)

The peak value (the highest measured temperature) and the peak time (the time at

which the peak values i s read) can be stored. These parameters for peak values can

be accessed by code 0037. The parameters are listed in Table 3 below.

Table 3. Alarm setting parameters.

Symbol

Name

Description

Peak value

mAt

Peak value time

mAt

End

Exit

Note 11. mA (Peak Value). The highest temperature reading. By defaul t this function is

turned on. The Peak Value will be kept in the memory unless cleared. After the unit is

powered on, the previously recorded Peak Value and its time stamp will remain in the

memory unless: 1) a new peak value overwrites the previous peak val u e, 2) or the

memory has been reset. Hold the Down key for 2 seconds will reset both the peak

value and its time stamp to 0. The recorded peak value can be checked by pressing

DOWN key during the normal operating mode; press DOWN key again to display the

Peak Value Ti m e; press and hold Down key for 2 seconds to clear the stored Peak

Value and the Peak Value Time.

Note 12. mAt (Peak Value Ti m e). The time stamp of the Peak Value. By defaul t this

function is turned on. The time is tracked by the build-in timer which is activated

whenever the mAt function is bei n g turned on. The current Peak Value Time wi l l be

overwritten by the new Peak value time. The Peak value time can be checked by

pressing DOWN key again in the peak value mode. Pressing the DOWN key 2 seconds

will clear the Peak value as well as the Peak value time. Every time the unit is restarted

or the Peak Value is cleared, the timer will start over agai n (unit i n seconds).

12. Communication Between the Master Unit and Slave Units.

When the communication between a master unit and a slave uni t is establ i shed, all the

settings and operations on these two units are mirrored , except for the Unit ID and

the operation which temporarily mute the alarm (for the safety reason). You can set al l

of these parameters from either the slave or the master unit.

1) Mirrored operations and parameters. Operations and readings on one unit will be

mirrored to the other unit. Change of the alarm setting on the master uni t will also be

synchronized to the slave unit, or vice versa. The temperature reading and peak

values on the slave unit will also be synchronized between the master unit and the

slave unit. For example, when the peak value is cleared from the slave unit, the new

peak value will be recorded at the slave unit and then mirrored to the master unit.

When the peak val u e is cleared from the master unit, this operation will also be

synchronized to the slave unit, and the peak value will be cleared.

2) Muting the alarms. When you press the SHIFT key to mute the alarm buzzer, it will

only be effective to the buzzer on this unit. The buzzer on the other unit will continue

sound until temperature left the alarm zone, or the SHIFT key on that unit is pressed.

3) Placing distance. Placing the master and the slave units too far or too close will

result in bad signal reception on the master unit. Signal reception can be affect by

distance, physical obstacles, and other factors. The master unit and the slave unit can

be placed 100 feet away from each other in an open space.

Figure 6. Velcro mounti n g (left) and stainl e ss steel plate mounting (right).

2015.08

Sett ing Range

Initial

Note

On/off

11. Placing and Mounting the Meter.

The meter should be pl a ced in a working environment where temperature is -20-50° C

(0-100° F). It should be pl a ced away from hi g h heat to protect the plastic housing and

electronics. Two mounting opti o ns are provided:

1) A pair of Velcro fastener. The Velcro has a pressure sensi t ive adhesive backing. You

can remove the protective fi l m from the hook piece and stick it to the back of the meter

(see Figure 6). Then remove the protective film from the loop piece and install it onto

the wall. Please note that the pressure sensitive adhesive on Vel c ro is industrial grade

with strong holding force. It needs to be stick on a solid surface. Don t put it on a drywall

because i t may peel off the paint if you decided to remove it later.

2) A stainless steel mounting plate. The plate allows the meter to be hung on a hook or

a nail. It also allows the meter to be permanently mounted with a screw. The bottom

part of the stai n less steel mounti n g plate is covered with pressure sensitive adhesive.

To install it onto the meter, peel off the pink colored releasing film; press it firmly onto

the back of the meter (see figure 6).

NOTE: This equi p ment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference i n a residential installation.

This equi p ment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equi p ment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the

receiver i s connected.

4) Consult the dealer or an experienced radi o /TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitl y approved by

manufacturer could voi d your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference recei v ed, including interference that may

cause undesired operation.

Auber Instruments

5755 North Poi n t Parkway, Suite 99

Alpharetta, GA 30022

www.auberins.com

Email: [email protected] Tel: 770-569-8420

No part of this manual shall be copied, reproduced, or transmitted in any way without

the prior, written consent of Auber Instruments. Auber Instruments retains the

exclusive rights to all information included in this document.

WWW.AUBERINS.COM

P3/3