3onedata IES205G Manuale d'uso - Pagina 3

Sfoglia online o scarica il pdf Manuale d'uso per Router di rete 3onedata IES205G. 3onedata IES205G 4. Unmanaged industrial ethernet switch

Stampa la pagina

【LED Indicator】

The led indicator light on the front panel of product, the

function of each LED is described in the table as below.

LED system status

LED

Status

Description

Power is connected and operates

properly.

PWR

Power is not connected or

OFF

operates abnormally.

Port made effective connection

Link/ACT

Blinking

Port is inactive status

(G1~G5)

Port did not make effective

OFF

connection

【Installation】

Before installation, ensure that the work environment meets

the installation requirements, including the power needs and

abundant space. Whether it is close to the connection

equipment and other equipment are prepared or not.

1. Avoid in the sunshine, keep away from the heat

fountainhead or the area wherein intense EMI.

2. Check

the

cables

and

plugs

requirements.

3. Check whether the cables be seemly or not (less than

100m) according to the reasonable scheme.

4. Power: 12~48VDC

5. Environment: Working temperature: -40～75℃

Storage Temperature: -40～85℃

Relative humidity 5%～95%

DIN Rail Installation

In order to use in industrial environments expediently, the

product adopts 35mm DIN-Rail installation, the installation

steps are shown as follows:

Examine the DIN-Rail attachment

Examine DIN Rail whether be firm and the position is

suitability or not.

Insert the top of the DIN-Rail into the slot just below the

stiff metal spring.

The DIN-Rail attachment unit will snap into place as

shown below.

Wiring Requirements

Cable laying needs to meet the following requirements,

1. It is needed to check whether the type, quantity, and

specification of cable match the requirement before

cable laying;

2. It is needed to check the cable is damaged or not, factory

records and quality assurance booklet before cable

laying;

that

installation

3. The required cable specification, quantity, direction and

laying position need to match construction requirements,

and cable length depends on actual position;

4. All the cable cannot have break-down and terminal in the

middle;

5. Cables should be straight in the hallways and turn;

6. Cable should be straight in the groove, and cannot

beyond the groove in case of holding back the inlet and

outlet holes. Cables should be banned and fixed when

they are out of the groove;

7. User cable should be separated from the power lines.

Cables, power lines, and grounding lines cannot be

overlapped and mixed when they are in the same groove

road. When cable is too long, it cannot hold down

another cable, but structure in the middle of alignment

- 3 -

rack;

8. Pigtail cannot be tied and served as less as possible.

Swerving radius cannot be too small (small swerving

causes terrible loss of link). It's banding should be

moderate, not too tight, and should be separated from

other cables;

9. It should have corresponding simple signal at both sides

of the cable for maintaining.

【Specification】

Technology

Standard:

IEEE802.3,

IEEE802.3u,

IEEE802.3ab

Flow control: IEEE802.3x flow control, back press flow

control

Exchange Attribute

100M forward speed: 148810pps

1000M forward speed: 1488100pps

100M maximum filter speed: 148810pps

1000M maximum filter speed: 1488100pps

Transmit mode: store and forward

System exchange bandwidth: 14G

MAC address table: 8K

Memory: 1Mbit

Interface

Electric port: 10/100/1000Base-T(X) auto negotiation speed,

Full/Half duplex mode, auto MDI/MDI-X connection, and

RJ45 connector.

Transfer Distance

Twisted cable: 100M (standard CAT5/CAT5e cable)

LED Indicator

Interface indicators: Link/ACT (1~5)

Power Indicator: PWR

Power Supply

Input voltage: 12～48VDC

Type of input: 3-pin 7.62mm pitch terminal block

IEEE802.3x,