Freedom Air 2.0 Istruzioni per il funzionamento - Pagina 2

Sfoglia online o scarica il pdf Istruzioni per il funzionamento per Pompa dell'acqua Freedom Air 2.0. Freedom Air 2.0 3. Dual remote wireless interchangeable inflator pump

Stampa la pagina

will decrease relative to pressure in air chamber, and scroll bar will scroll down to show that the pressure

is decreasing. At any time during the period of deflation, pressing any button will stop the deflation. Or

when the pressure reaches the minimum ("0" on LCD), the deflation will stop automatically.

6. Memory: press "MEM1" or "MEM2" button, LCD will show "M1" or "M2" and the pump will be activated to

inflate or deflate until the pressure in air chamber reaches the level memorized. When the pump is

inflating or deflating to the level memorized, pressing any button will still stop inflation or deflation.

7. Setting Memory Level: when LCD shows a pressure level readout, before or after inflation or deflation,

press and hold "MEM1" or "MEM2" button for 3 seconds, M1 or M2 indicator will flash and the current

pressure level will be kept as a new memory level. The memory level for left or right side air chamber can

be set in the same way, to be same or different. The default MEM1 level is 25mmHg ("25" on LCD). The

default MEM2 level is 20 mmHg ("20" on LCD).

8. Smart Support Technology： SST is enabled by default to maintain level last selected or memory setting for

continuous comfort. SST may be disabled/enabled by pressing "LEFT/RIGHT" for 3 seconds then, while

still pressing "LEFT/RIGHT" button, quickly pressing "FIRM" button at which time LCD will display F1, at

this time pressing "LEFT/RIGHT" will turn SST off or on. When disabled SST symbol will not show in the

LCD display.

9. Actual Pressure Check: press and hold "LEFT/RIGHT" for 3 seconds then, while still pressing

"LEFT/RIGHT L" button, quickly pressing "MEM2" button, LCD will display the actual pressure in air

chamber and the pressure scroll bar will flash. The display of actual pressure will turn off after 15 seconds

automatically or by pressing any button.

10. Special Note: A) The Max. pressure is 50mmHg. B) The pump will automatically stop after working

continuously for 10 minutes. C) Real-time Pressure readout has a 10 mmHg margin when starting inflation,

however, the real-time pressure will be displayed directly when it is lower than 10mmHg. After checking

the actual pressure, the actual pressure will be treated as the last set level. D) Air Chamber Dimension

Detection: to display the pressure level in air chamber accurately, Freedom-Air 2.0 Wireless Inflator Pump

has a function to measure and record air chamber dimension automatically when it works in the first few

times. Such a measurement can also be done manually by pressing "LEFT/RIGHT" button for 3 seconds

then, while still pressing "LEFT/RIGHT" button, quickly pressing "SOFT" button at which time LCD will

display AD and the inflator pump will start the measurement. It takes about 10 minutes to do such a

measurement.

11. Troubleshooting:

controller will show "Er". B) Sync: while remotes are synced before delivery, if "Er" continues to show on

LCD or when the wireless remote is replaced, please resync. To resync, disconnect power to the pump,

then power it on again, the power indicator will flash slowly for 30 seconds. Within 30 seconds, press any

button to light LCD, then press down "FIRM" button for 3 seconds and when the LCD shows "SU" the

pump and remote are synced again successfully. C) Batteries: The remote is powered by three

AAA-LR03-1.5V batteries. When the battery power is low, the LCD will show low battery capacity alert so

please replace the batteries. If remote will not be used for a long time, please remove batteries.

Range: wireless remote control range is 15-30' (5-10m) so if out of range the