Constellation audio Inspiration INTEGRATED 1.0 Manuale d'uso - Pagina 15
Sfoglia online o scarica il pdf Manuale d'uso per Amplificatore Constellation audio Inspiration INTEGRATED 1.0. Constellation audio Inspiration INTEGRATED 1.0 16.
Stampa la paginaMaintenance
The Inspiration Integrated requires no regular maintenance.
If the unit's surface becomes dusty, simply wipe it off with a soft dry cloth. Do not spray cleaners on the sur-
face. To clean fingerprints from the surface of the integrated amplifier, spray a small amount of mild window
cleaner such as Windex onto a soft dry cloth, then use the cloth to remove the fingerprints. Do not spray the
cleaner directly onto the amplifier.
Troubleshooting
Unit will not turn on
1. First, check to see if the rear master power switch is on. If it is, try the following steps in order. After you
perform each step, touch the touchscreen on the front of the unit. If it illuminates, the unit is functioning cor-
rectly and there is no need to continue to the next steps.
A. Check power cable connections between the wall and the Inspiration Integrated. Push the wall plug
and the connector at the power supply in firmly.
B. If the Inspiration Integrated is plugged into an AC line conditioner, make sure the line conditioner is
turned on.
C. Flip the master power switch off and on again. This will reset the Inspiration Integrated's internal cir-
cuit breaker.
D. Check the circuit breaker for the AC circuit that the Inspiration Integrated is plugged into. If the break-
er is tripped, flip it back on. If it will not turn on, there is likely a short circuit somewhere in the lines or in
a device connected to this AC circuit. Check the power cords for your components to make sure none
have been damaged.
E. If none of these conditions restores power, it is possible one of the Inspiration Integrated's internal fuses
is blown. Do not attempt to change the fuse yourself—the Inspiration Integrated requires the use of spe-
cial high-voltage fuses that are not commonly available. Contact your Constellation dealer.
Unit is on but no sound is produced
1. If the front touchscreen is blank, touch it. If it illuminates and shows anything other than the onscreen Pow-
er button, the unit is on. If it shows the onscreen Power button, touch the button to power up the unit.
2. If the front touchscreen shows the message "Powering On," wait about 10 seconds. Once the unit is
warmed up, an input screen should appear and the sound should come from the speakers or headphones.
3. If the volume numbers on the LCD panel are flashing, hit the Mute button on the front panel or on the re-
mote to restore sound.
4. Make sure the correct output mode (speakers or headphone) is selected. This can be set only from an input
screen (see page 14). With an input screen selected, the fourth icon from the left, along the bottom of the
touchscreen, will show you if the unit is in speakers or headphone output mode. Press the button under the
icon to change the mode.
5. If none of the above steps restores the sound, try the following steps in order. If any one of the steps re-
stores the sound, there is no need to continue to the next steps.
A. Check you are on the correct input. Cycle through available inputs using the front touchscreen con-
trols, or select the desired input using the remote.
B. Check that the source component is on and playing back—i.e., if it is a CD player, make sure that the
CD is playing and not in pause mode.
C. Check the connections between the Inspiration Integrated and your speakers or headphones, and be-
tween the Inspiration Integrated and the audio source device. If a cable is disconnected, reconnect it. If
this does not restore sound, try substituting a different set of cables in order to make sure the original set
was functioning properly.
D. Check that the volume is at a sufficient level. Do not turn the volume all the way up to check this, as if
sound is reestablished while the Inspiration Integrated is set to output maximum volume, damage can be
done to your speakers and amplifiers.
15