- ページ 15

アンプ Constellation audio Inspiration INTEGRATED 1.0のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Constellation audio Inspiration INTEGRATED 1.0 16 ページ。

ページを印刷する

Maintenance

The Inspiration Integrated requires no regular maintenance.

If the unit's surface becomes dusty, simply wipe it off with a soft dry cloth. Do not spray cleaners on the sur-

face. To clean fingerprints from the surface of the integrated amplifier, spray a small amount of mild window

cleaner such as Windex onto a soft dry cloth, then use the cloth to remove the fingerprints. Do not spray the

cleaner directly onto the amplifier.

Troubleshooting

Unit will not turn on

1. First, check to see if the rear master power switch is on. If it is, try the following steps in order. After you

perform each step, touch the touchscreen on the front of the unit. If it illuminates, the unit is functioning cor-

rectly and there is no need to continue to the next steps.

A. Check power cable connections between the wall and the Inspiration Integrated. Push the wall plug

and the connector at the power supply in firmly.

B. If the Inspiration Integrated is plugged into an AC line conditioner, make sure the line conditioner is

turned on.

C. Flip the master power switch off and on again. This will reset the Inspiration Integrated's internal cir-

cuit breaker.

D. Check the circuit breaker for the AC circuit that the Inspiration Integrated is plugged into. If the break-

er is tripped, flip it back on. If it will not turn on, there is likely a short circuit somewhere in the lines or in

a device connected to this AC circuit. Check the power cords for your components to make sure none

have been damaged.

E. If none of these conditions restores power, it is possible one of the Inspiration Integrated's internal fuses

is blown. Do not attempt to change the fuse yourself—the Inspiration Integrated requires the use of spe-

cial high-voltage fuses that are not commonly available. Contact your Constellation dealer.

Unit is on but no sound is produced

1. If the front touchscreen is blank, touch it. If it illuminates and shows anything other than the onscreen Pow-

er button, the unit is on. If it shows the onscreen Power button, touch the button to power up the unit.

2. If the front touchscreen shows the message "Powering On," wait about 10 seconds. Once the unit is

warmed up, an input screen should appear and the sound should come from the speakers or headphones.

3. If the volume numbers on the LCD panel are flashing, hit the Mute button on the front panel or on the re-

mote to restore sound.

4. Make sure the correct output mode (speakers or headphone) is selected. This can be set only from an input

screen (see page 14). With an input screen selected, the fourth icon from the left, along the bottom of the

touchscreen, will show you if the unit is in speakers or headphone output mode. Press the button under the

icon to change the mode.

5. If none of the above steps restores the sound, try the following steps in order. If any one of the steps re-

stores the sound, there is no need to continue to the next steps.

A. Check you are on the correct input. Cycle through available inputs using the front touchscreen con-

trols, or select the desired input using the remote.

B. Check that the source component is on and playing back—i.e., if it is a CD player, make sure that the

CD is playing and not in pause mode.

C. Check the connections between the Inspiration Integrated and your speakers or headphones, and be-

tween the Inspiration Integrated and the audio source device. If a cable is disconnected, reconnect it. If

this does not restore sound, try substituting a different set of cables in order to make sure the original set

was functioning properly.

D. Check that the volume is at a sufficient level. Do not turn the volume all the way up to check this, as if

sound is reestablished while the Inspiration Integrated is set to output maximum volume, damage can be

done to your speakers and amplifiers.