CAST Lighting Impressionist CIWL6 Manuale di avvio rapido - Pagina 2

Sfoglia online o scarica il pdf Manuale di avvio rapido per Luce per esterni CAST Lighting Impressionist CIWL6. CAST Lighting Impressionist CIWL6 2. Led wall wash light
Anche per CAST Lighting Impressionist CIWL6: Manuale di avvio rapido (2 pagine)

Stampa la pagina

CAST Lighting Impressionist CIWL6 Manuale di avvio rapido

Electrical Requirements

Input Voltage:

10-24V AC/DC

Power Supply*:

Must use a toroidal magnetic

transformer to supply low

voltage power (such as CAST

Journeyman, Master, and

Perimeter Series).

Wire:

For maximum system longevity,

use tin-coated marine-grade wire

(such as CAST No-Ox

Wire).

Connectors:

For connecting single or multiple

wires, use robust waterproof con-

nectors and junctions (such as

CAST Spider Splice Junction Box

and CAST Butt Crimp Connectors).

*Use of approved power supply acti-

vates extended warranty.

Electrical Consumption:

Wattage: 8.3 W

Power Factor: 8.7

Volt-Amps: 9.5 VA

(for wire and transformer sizing;

and voltage loss calculations)

• WARNING - Risk of Electric Shock. Install all luminaires

less than 10 ft. (3.05 m) or more from a pool, spa, or

fountain.

• Follow NEC guidelines for outdoor low voltage wiring.

• Obey all local electrical codes and requirements.

• Use only 25A/circuit 12-volt power supply.

• A luminaire shall not use tungsten halogen lamps unless

the luminaire is marked for such lamps.

• The luminaire's low voltage cable shall:

a. be protected by routing in close proximity to the

luminaire or fitting, or next to a building structure

such as a house or deck;

b. not be buried except for a maximum 6 inches (15.2

cm) in order to connect to the main low voltage

cable.; and,

3c. Large Talon Stake Mounting Instructions.

• To assemble stake, insert flat end of each spike into stake body receptacles. Secure set

screws with 3/32" hex bit.

• Prepare turf or bed area by removing plant material or mulch to attain a firm soil surface

of about 6" diameter. Tamp down soil and test with bubble level to ensure surface is

level. If desired (for aesthetic reasons), Talon Stake body can be set 1" below grade then

covered with soil or mulch.

• Position stake so wire opening faces wire trench.

• Drive stake into ground prior to attaching fixture. Use rubber or dead blow mallet to drive

talon into ground. Strike directly above each spike in turn, driving stake into ground in

steady increments to ensure pins enter vertically. Continue striking until body is firmly

seated in soil.

• Extend narrow trench to directly beneath center of stake. Insert fixture lead wire through

wire opening. Insert fixture stem into stake receptacle. Secure thumb screw. Back-fill

wire trench and, if needed, cover stake with soil or mulch.

L UM I N A I R E A D JUSTME NT S

For Impressionist Only! (CIWL6)

NOTE: CWL6LED1 is a fixed output lumen fixture.

1. LIGHT LEVEL ADJUSTMENT INSTRUCTIONS.

All CAST Impressionist Series fixtures have built-in light level control. This can be acti-

vated in two ways - using the provided Manual Dimmer Control Jumper Cable or with

the CAST Impressionist Dimmer Control (CDIMMER). Both of these devices plug into the

Fixture Control Plug located on the fixture lead wire.

• Manual Dimmer Control Jumper Cable (CIJ). Plugging this device into the fixture wire

Control Plug will activate the dimming (up or down) sequence. Each time the device is

plugged in (while fixture is powered) the dimming cycle reverses. As long as the device

is plugged in, the fixture will dim up or down until the maximum (100%) or minimum (5%)

is reached. If the plug is left in place for 15 sec. after either of these limits are reached,

then the fixture resets to 100%. When the device is unplugged, the fixture retains the

specific light level even when not powered.

• CAST Impressionist Dimmer Control (CDIMMER). Connect CDIMMER plug to fixture wire

Control Plug. Switch unit "ON". Depress and hold "DIM" button to dim light up or down.

Each time button is depressed, dimming direction reverses. To bring fixture to 100%,

depress and hold button for 15 sec. Store unit in cool dry place. Change batteries yearly.

SA F E T Y INS T RU CTIONS

c. have the length cut off so that it is connected to a

connector within 6 inches (15.2 cm (from a building

structure, a luminaire, or fitting.

• Contact only switch or plug when turning system on or off

at transformer.

• Do not look directly into a lighted lamp.

• Do not operate the lighting fixture if damaged.

• Do not mount stake mounted fixtures in tree application.

Use Tree-Mount fixture only!!

• Unplug transformer while installing and connecting lumi-

naires.

• Main low voltage cable is intended for shallow burial - less

than 6" (152 mm) - unless the manufacturer has provided

wiring suitable for direct burial.