HI 54110 Manuale - Pagina 2

Sfoglia online o scarica il pdf Manuale per Miglioramento della casa HI 54110. HI 54110 4. Self-inflating santa claus

Stampa la pagina

Self-Inflating Santa Claus

item no.: 54110

directioNS for uSe ANd

SAfety iNStructioNS

Make yourself familiar with the product before first use.

Read the following directions for use and safety instructions

carefully. Use this product only for its intended purpose.

Keep these instructions for future reference and include

these instructions if you pass on the product to third parties.

iNteNded uSe

Use the product only for lighting decoration. Any other use

as well as modifications of the product have to be consi-

dered as improper use and could cause injuries or product

damages. The manufacturer will not be held responsible

for any damages resulting from such improper use. Not for

commercial use.

SAfety iNStructioNS

⚠

WArNiNg

Life and accident risk for toddlers and kids! To

avoid danger of suffocation, keep packing ma-

terials away from babies and children. Risk of

suffocation due to packing material. Small parts

can be swallowed! Children often underestimate

the dangers!

iNStAllAtioN iNStructioNS

· The item is for indoor and outdoor use. Please notice the

following instructions:

· The bottom of the inflatable figure contains the fan with its

suction hole. Insure that the suction hole is not covered.

Please clean the installation site from light material, i.e.

leafs, grass, sand, snow etc., before placing the figure.

Fire danger!

· The power supply with the lighting chain plug should be

placed indoor

· Situated near to the fan is a zipper. The zipper is used for

fast venting of the figure. Ensure that it is closed before

initial operation.

iNitiAl operAtioN

· Unpack figure and power supply carefully.

· Spread out the figure on the ground at the installation site.

Do not damage the textile shell.

· Plug the power supply into a power socket. The fan starts

to inflat the figure and the LED lights illuminate.

· In the beginning you should lift the fan a little bit so that

the suction hole gets enough fresh air. If the figure is in-

flated sufficiently the fan is situated above the ground

automatically.

· Inflating of the figure happens within a few minutes. After

the figure has been inflated completely and it is situated

outdoor, you should secure it with the attached sticks and

ropes against windy conditions. In the bottom you can find

four hangers and in the middle three further hangers. Ple-

ase fix the attached ropes to the hangers at the middle of

the figure. Anchor the other ends of the ropes with sticks

as well and put the sticks into the ground. On a terrace or

a balcony please fix the figure with ropes at the balustrade

for example.

· Pay attention that ropes and sticks give a little tension to

the figure without harming the textile shell.

· Note: if the power supply is taken out of the socket the

figure deflates and the LED lights go out.

trouBleShootiNg

If the figure becomes not inflated while the fan is running

very probably the textile shell is damaged.

Please look carefully for a hole in the shell. A little hole can

be closed with special glueing tape. If there is a big hole

please constrict it first with needle and thread. After that it

should be sealed with glueing tape as well.

techNicAl detAilS

· Height: approx. 180 cm

· Including transformer

· Input: 230 V~, 50 Hz

· Output: 12 V⎓, 700 mA, max. 8.4 W

eNviroNMeNtAl Note

Electrical and Electronic Equipment must not be

dispose by residual waste. If you want to part from

a product, inform yourself at your local facilities

about a proper disposal of electronic waste accor-

ding to WEEE directive 2012/19/EU.