- ページ 2
ホームインプルーブメント HI 54110のPDF マニュアルをオンラインで閲覧またはダウンロードできます。HI 54110 4 ページ。 Self-inflating santa claus
ページを印刷するGB
Self-Inflating Santa Claus
item no.: 54110
directioNS for uSe ANd
SAfety iNStructioNS
Make yourself familiar with the product before first use.
Read the following directions for use and safety instructions
carefully. Use this product only for its intended purpose.
Keep these instructions for future reference and include
these instructions if you pass on the product to third parties.
iNteNded uSe
Use the product only for lighting decoration. Any other use
as well as modifications of the product have to be consi-
dered as improper use and could cause injuries or product
damages. The manufacturer will not be held responsible
for any damages resulting from such improper use. Not for
commercial use.
SAfety iNStructioNS
⚠
WArNiNg
Life and accident risk for toddlers and kids! To
avoid danger of suffocation, keep packing ma-
terials away from babies and children. Risk of
suffocation due to packing material. Small parts
can be swallowed! Children often underestimate
the dangers!
iNStAllAtioN iNStructioNS
· The item is for indoor and outdoor use. Please notice the
following instructions:
· The bottom of the inflatable figure contains the fan with its
suction hole. Insure that the suction hole is not covered.
Please clean the installation site from light material, i.e.
leafs, grass, sand, snow etc., before placing the figure.
Fire danger!
· The power supply with the lighting chain plug should be
placed indoor
· Situated near to the fan is a zipper. The zipper is used for
fast venting of the figure. Ensure that it is closed before
initial operation.
iNitiAl operAtioN
· Unpack figure and power supply carefully.
· Spread out the figure on the ground at the installation site.
Do not damage the textile shell.
· Plug the power supply into a power socket. The fan starts
to inflat the figure and the LED lights illuminate.
· In the beginning you should lift the fan a little bit so that
the suction hole gets enough fresh air. If the figure is in-
flated sufficiently the fan is situated above the ground
automatically.
· Inflating of the figure happens within a few minutes. After
the figure has been inflated completely and it is situated
outdoor, you should secure it with the attached sticks and
ropes against windy conditions. In the bottom you can find
four hangers and in the middle three further hangers. Ple-
ase fix the attached ropes to the hangers at the middle of
the figure. Anchor the other ends of the ropes with sticks
as well and put the sticks into the ground. On a terrace or
a balcony please fix the figure with ropes at the balustrade
for example.
· Pay attention that ropes and sticks give a little tension to
the figure without harming the textile shell.
· Note: if the power supply is taken out of the socket the
figure deflates and the LED lights go out.
trouBleShootiNg
If the figure becomes not inflated while the fan is running
very probably the textile shell is damaged.
Please look carefully for a hole in the shell. A little hole can
be closed with special glueing tape. If there is a big hole
please constrict it first with needle and thread. After that it
should be sealed with glueing tape as well.
techNicAl detAilS
· Height: approx. 180 cm
· Including transformer
· Input: 230 V~, 50 Hz
· Output: 12 V⎓, 700 mA, max. 8.4 W
eNviroNMeNtAl Note
Electrical and Electronic Equipment must not be
dispose by residual waste. If you want to part from
a product, inform yourself at your local facilities
about a proper disposal of electronic waste accor-
ding to WEEE directive 2012/19/EU.