Great Plains Industries GPRO PRO25-012PO/XTS Manuale d'uso - Pagina 2
Sfoglia online o scarica il pdf Manuale d'uso per Pompa dell'acqua Great Plains Industries GPRO PRO25-012PO/XTS. Great Plains Industries GPRO PRO25-012PO/XTS 8.
Stampa la paginaGENERAL INFORMATION
The purpose of this manual is to assist you in install-
ing, operating and maintaining your GPRO
manual covers models PRO25-012 (12-Volt DC) and
PRO25-024 (24-Volt DC).
Model Components
PRO25-024PO / PRO25-012PO: Includes pump only.
PRO25-012PO/XTS: Includes pump only and compo-
nents to assemble to unit before use.
NOTE: Suffixes PO and PO/XTS are for ordering purposes
only. Constructions described above are covered as
alternate constructions under the Part No. PRO25
UL Listing.
An automatic bypass valve prevents pressure build
up when the pump is on with the nozzle closed. To
avoid damage, do not run the pump more than 10
minutes with the nozzle closed.
The duty cycle of this pump is 30 minutes ON and 30
minutes OFF. Allow the pump to cool for 30 minutes.
This pump is designed for use only with gasoline (up
to 15% alcohol blends such as E-15), diesel fuel (up to
20% biodiesel blends such as B20) and kerosene. Do
not use this pump for dispensing any fluids other than
those for which it was designed. To do so may damage
pump components and will void the warranty.
This pump is designed to operate on a typical DC automo-
tive electrical system. The pump is designed to operate
with the appropriate DC voltage at the motor leads and
the ratings are determined at this voltage. Performance
may vary due to length of power cord, battery condition
or output from the vehicle charging system that will affect
system voltage.
Do not leave the system running with fluids. "Dry running"
can damage the pump.
Do not pump the tank completely dry, as contaminants
from the bottom of the tank may enter the pump.
SAFETY INSTRUCTIONS
The following safety alert symbols are used in
this manual. Obey all safety messages that follow
this symbol to avoid possible injury or death.
DANGER
WARNING
2
®
pump. This
DANGER indicates an
imminently hazardous
situation which, if not avoid-
ed, will result in death or
serious injury.
WA R N I N G i n d i c a t e s
a potentially hazardous
situation which, if not avoid-
ed, could result in death or
serious injury.
CAUTION
There are inherent dangers wherever flammable fuel and
AC electrical sources are in close proximity.
Static electricity as a source of sparking is always a
concern and requires extreme care in the installation and
operation of your entire fuel transfer system.
Additional components such as meters, automatic nozzles
and filters must be listed for use with fuel transfer systems.
The flow of fuel through a hose and nozzle can generate
static electrical charges and dangerous sparking can
result in fire or explosion. Hoses and nozzles must be
electrically conductive and bonded to ground.
It is your responsibility to:
• Know and follow applicable national, state and local
safety codes pertaining to installing and operating
electrical equipment for use with flammable liquids.
• Know and follow all safety precautions when handling
petroleum fuels.
• Ensure that all equipment operators have access to
adequate instructions concerning safe operating and
maintenance procedures.
Observe all safety precautions concerning safe handling
of petroleum fuels.
To ensure safe operation, all fuel transfer systems must
be properly grounded. Proper grounding means a continu-
ous metal-to-metal contact from one component to the
next, including tank, bung, pump, meter, filter, hose and
nozzle. Care should be taken to ensure proper grounding
during initial installation and after any service or repair
procedures. For your safety, please take a moment to
review the warnings below.
To prevent physical injury, observe precautions against
fire or explosion when dispensing fuel. Do not operate
the system in the presence of any source of ignition
including running or hot engines, lighted cigarettes, or
gas or electric heaters.
Observe precautions against electrical shock when oper-
ating the system. Serious or fatal shock can result from
operating electrical equipment in damp or wet locations.
Inspect external pump wiring regularly to make sure it is
correctly attached to the battery. To avoid electrical shock,
use extra care when connecting the pump to power.
Avoid prolonged skin contact with petroleum fuels. Use
protective goggles, gloves and aprons in case of splash-
ing or spills. Change saturated clothing and wash skin
promptly with soap and water.
Observe precautions against electrical shock when
servicing the pump. Always disconnect power before
repairing or servicing. Never apply electrical power to
the system when any of the coverplates are removed.
If using solvent to clean pump components or tank, ob-
serve the solvent manufacturer's recommendations for
safe use and disposal.
C A U T I O N
i n d i c a t e s
a potentially hazardous
situation which, if not avoid-
ed, may result in minor or
moderate injury.