Great Plains Industries GPRO PRO25-012PO/XTS 소유자 매뉴얼 - 페이지 2

{카테고리_이름} Great Plains Industries GPRO PRO25-012PO/XTS에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Great Plains Industries GPRO PRO25-012PO/XTS 8 페이지.

페이지 인쇄

GENERAL INFORMATION

The purpose of this manual is to assist you in install-

ing, operating and maintaining your GPRO

manual covers models PRO25-012 (12-Volt DC) and

PRO25-024 (24-Volt DC).

Model Components

PRO25-024PO / PRO25-012PO: Includes pump only.

PRO25-012PO/XTS: Includes pump only and compo-

nents to assemble to unit before use.

NOTE: Suffixes PO and PO/XTS are for ordering purposes

only. Constructions described above are covered as

alternate constructions under the Part No. PRO25

UL Listing.

An automatic bypass valve prevents pressure build

up when the pump is on with the nozzle closed. To

avoid damage, do not run the pump more than 10

minutes with the nozzle closed.

The duty cycle of this pump is 30 minutes ON and 30

minutes OFF. Allow the pump to cool for 30 minutes.

This pump is designed for use only with gasoline (up

to 15% alcohol blends such as E-15), diesel fuel (up to

20% biodiesel blends such as B20) and kerosene. Do

not use this pump for dispensing any fluids other than

those for which it was designed. To do so may damage

pump components and will void the warranty.

This pump is designed to operate on a typical DC automo-

tive electrical system. The pump is designed to operate

with the appropriate DC voltage at the motor leads and

the ratings are determined at this voltage. Performance

may vary due to length of power cord, battery condition

or output from the vehicle charging system that will affect

system voltage.

Do not leave the system running with fluids. "Dry running"

can damage the pump.

Do not pump the tank completely dry, as contaminants

from the bottom of the tank may enter the pump.

SAFETY INSTRUCTIONS

The following safety alert symbols are used in

this manual. Obey all safety messages that follow

this symbol to avoid possible injury or death.

DANGER

WARNING

pump. This

DANGER indicates an

imminently hazardous

situation which, if not avoid-

ed, will result in death or

serious injury.

WA R N I N G i n d i c a t e s

a potentially hazardous

situation which, if not avoid-

ed, could result in death or

serious injury.

CAUTION

There are inherent dangers wherever flammable fuel and

AC electrical sources are in close proximity.

Static electricity as a source of sparking is always a

concern and requires extreme care in the installation and

operation of your entire fuel transfer system.

Additional components such as meters, automatic nozzles

and filters must be listed for use with fuel transfer systems.

The flow of fuel through a hose and nozzle can generate

static electrical charges and dangerous sparking can

result in fire or explosion. Hoses and nozzles must be

electrically conductive and bonded to ground.

It is your responsibility to:

• Know and follow applicable national, state and local

safety codes pertaining to installing and operating

electrical equipment for use with flammable liquids.

• Know and follow all safety precautions when handling

petroleum fuels.

• Ensure that all equipment operators have access to

adequate instructions concerning safe operating and

maintenance procedures.

Observe all safety precautions concerning safe handling

of petroleum fuels.

To ensure safe operation, all fuel transfer systems must

be properly grounded. Proper grounding means a continu-

ous metal-to-metal contact from one component to the

next, including tank, bung, pump, meter, filter, hose and

nozzle. Care should be taken to ensure proper grounding

during initial installation and after any service or repair

procedures. For your safety, please take a moment to

review the warnings below.

To prevent physical injury, observe precautions against

fire or explosion when dispensing fuel. Do not operate

the system in the presence of any source of ignition

including running or hot engines, lighted cigarettes, or

gas or electric heaters.

Observe precautions against electrical shock when oper-

ating the system. Serious or fatal shock can result from

operating electrical equipment in damp or wet locations.

Inspect external pump wiring regularly to make sure it is

correctly attached to the battery. To avoid electrical shock,

use extra care when connecting the pump to power.

Avoid prolonged skin contact with petroleum fuels. Use

protective goggles, gloves and aprons in case of splash-

ing or spills. Change saturated clothing and wash skin

promptly with soap and water.

Observe precautions against electrical shock when

servicing the pump. Always disconnect power before

repairing or servicing. Never apply electrical power to

the system when any of the coverplates are removed.

If using solvent to clean pump components or tank, ob-

serve the solvent manufacturer's recommendations for

safe use and disposal.

C A U T I O N

i n d i c a t e s

a potentially hazardous

situation which, if not avoid-

ed, may result in minor or

moderate injury.