Automatic Technology Australia EasyRoller GDO-4 Istruzioni per l'installazione e manuale d'uso - Pagina 11

Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso per Apriporta del garage Automatic Technology Australia EasyRoller GDO-4. Automatic Technology Australia EasyRoller GDO-4 16.

Stampa la pagina

7.2

OPEN

OBSTRUCTION

FORCE

ADJUSTMENT

(a)

Fully close

the door

pressing

and

holding

the

green

inch button.

The

door

will stop

automatically when

the closed

limit

position

reached.

(b)

Turn

the

Green

Force Shaft

fully

clockwise. Press the

Yellow

O/S/C (open, stop,

close)

button

(see

Fig.17) momentarily, the

door

should

start

opening. As

the door

is opening

turn the Green

Shaft

slowly

anticlockwise

until the

door

stops.

(c)

Turn

the

Green

Shaft

10"

clockwise. Press

theYellow

button

open the

door. lf the

door stops

by itself, readjust

theGreen

Shaft a

further

clockwise. Keep

adlusting

this manner

until

the

door

can

complete

the

full opening

cycle.

7.3 CLOSE SAFETY

OBSTRUCTION

TEST

The door

now has

be tested

for

response

an obstruction

while

opening

and

closing. With the

door

in the

opened

position, place a solid

object approximately

metre

height

underthe door (see

Fig. 18). Press

"the

Yellow button

close the

door.

When

the door

reaches

and

pushes

\-.ie

object

should

pause

then

reverse up

the

open

position. Repeat

the

above

and

observe

the

action of the

door as

it pushes against the

solid object. Undue load

should

not be applied to the

door.

The

load

imposed by

the door

should be around

10k9.

The

load

can

tesied

by placing

bathroom scale on the

floor

under the door,

start

a close

cycle and

read

the scale

as the

door

pushes down against

the

scale. lf the

reading is

too high.

readjust

the

Red

Force Shaft. Turning shaft

clockwise increases

the

load applied to

the

door.

Turning shaft

anticlockwise decreases

the

load applied

the

door.

IMPORTANT:

THE

DOOR IS UNABLE

REVERSE WHEN

OBSTRUCTED DISCONTINUE USE.

SELECT

MANUAL MODE AND

CONTACT AUTOMATIC TECHNOLOGY AUSTRALIA PTY

LTD.

SETTING OF TRANSMITTER AND RECEIVER

SECURITY CODE

8.1

SETTING THE TRANSMITTER

(a)

Remove

the

sliding cover from

the

back of the Transmitter (see

Fig.19).

The

coding switches

are

located under the

slide of

back

cover

(see

Fig.

19).

\o)

Using

pen or

similar

instrument, move the

code

switches

as to

form

random looking pattern. For example

switches i,2,5,7,8,10

and

the off

position and

3,4,6,9,12

in the

on position (see

Fig.

19).

The selected

pattern forms the Transmitter Code.

(c)

Connect

the 9V

Battery

Transmitter. Slide

the

back cover

back into position.

8.2

STORING THE

TRANSM!fiER

CODE

INTO

THE

CONTROLLER'S

RECEIVER

The memory

in the

controller's

receiver

can store

60 different

transmitter codes.

(a)

Press

and

hold

the

Blue

Code

Set Button on

the

Control

Panel

(see

Fig.

20).

(b)

Press the Transmitter Button for approximately

two

seconds.

Pause for 2 seconds. Press the Transmitters Button again for

approximately

two

seconds.

(c)

Release

the Code Set

Button.

(d)

Press the Transmitter Button

to see if

it operates

the

door.

(e)

Uncoil the Antenna Wire

and stretch

out

against

the

Garage Wall

horizontal or

vertical direction (try and

keep

the

antenna

wire

away

from

metal objects). Secure

wire with

suitable fasteners. Do not cut

the

antenna

wire

coil

up.

IMPORTANT: Only operate

the Garage

Door Opener when the

Garage

Door is in full view and

free from

obstructions.

(o)

(b)(c)

AUTO

FIG.

1,.:,r$,,r