Automatic Technology Australia EasyRoller GDO-4 Istruzioni per l'installazione e manuale d'uso - Pagina 9
Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso per Apriporta del garage Automatic Technology Australia EasyRoller GDO-4. Automatic Technology Australia EasyRoller GDO-4 16.
Stampa la paginaOPEN
LIMIT
ADJUSTMENT
(g)
Press in
and
hold
the
Green
Open lnch
Button.
The door
should start
opening. Release
the
inch button
when
the
door
reaches
the
desired
open
position. lf
the Green
LED
(see
Fig. 10) is illuminated and the
desired limit
position
has
been
reached
then the
limit
adjustment
is
complete. lf
the Green
LED is illuminated
but
the
door has
not
reached,
or
has
gone
past the
desired
position,
you
have
to
adjust the
Green
Fine Adjustment Screw
(see
Fig.
10).
Adjust
the
screw
anticlockwise
to
open the
door
more. To
open
the door
less adjust the
screw clockwise. Each
complete
revolution of
the
adjustment screw
is
equal
to approximately
.1
Omm
of
door travel.
NOTE: lf
the door has
not reached
the
desired
limit position
by more
than 30mm, it
is recommended
that the
green limits
cam
be adjusted
again before
the
green
fine
adjustment screw is adjusted.
CLOSE
LIMIT
ADJUSTMENT
(h)
Press in
and
hold
the
Red
Close lnch
Button.
The
door should
start
closing. Release
the
inch bution
when
the
door
reaches the desired
y
closed
position, lf
the
Red LED
(see Fig.
I1)
is illuminated and the
desired
position has
been reached then
the
limit
adjustment
is
complete. lf
the
Red LED is illuminated but the
door has
not reached,
or
has
gone
past the
desired
position,
you
have
to
adjust
the
Red
Fine Adjustment Screw
(see
Fig.
11).
Adjust the screw anticlockwise
to
close
the door
less. To
open the
door
more adjust
the
screw
clockwise. Each
complete
revolution of
the
adjustment
screw
is equal
to approximately
1Omm
of door travel.
NOTE: if the
door has
not reached
the
desired
limit
position
by more
than
30mm,
then
it
is
recommended
that the
red
limits
cam
be
adjusted
aQain
before
the
red
fine
adjustment
screw is adjusted.
5.2 SETTING LIMITS
FOR
LEFT HAND
INSTALLATION
(a)
With
the
Drive Assembly
in
manual mode, move the
door
up by
hand
to
the
desired
open
position.
(b)
Remove
the
Light Diffuser
(see
Fig. 9). Rotate by
hand
in
a
clockwlse
direction
the Green
Limit
Cam (see
Fig. 13) until the
cam
clicks the
open limit switch.
b)
Move
the door
down by hand
to
the desired closed position.
St(d)
Rotate by
hand
in
an
anticlockwise direction
the
red limit
cam
(see
Fig.14) until the
cam
clicks
the close
limit switch.
(e)
Connect
Power Lead from
the
Drive Assembly
into
a
general
purpose
power
outlet installed
by
a
licensed
qualified
electrical contractor.
Make sure
that the
Power Lead is safely fastened away
from
any
moving
parts.
Turn
the
Power On.
(f)
Re-engage the
drive
gear
to door
by pulling down on
the string
handle
and
then
releasing
slowly (see
Fig.
12).
OPEN
LIMIT
ADJUSTMENT
(S)
Press in
and
hold the Green
Open lnch
Button.
The door
should
start opening.
Release
the
inch button when the
door
reaches the
desired
open
limit
stop
position. lf
the Green
LED
(see
Fig. 13)
is
illuminated and
the
desired limit
stop position
has
been
reached then
the
limit
adjustment
is complete. lf
the
Green
LED
is illuminated
but
the door
has
not
reached
the
desired position,
you
have
to
adjust the
Green
Fine
Adjustment
Screw
(see
Fig.
13). To
open
the door
more,
adjust
the
screw anticlockwise.
To
open
the door
less adjust
the
screw
clockwise. Each
complete
revolution of
the
adjustment screw is equal
to
approximately
'lomm
of door travel.
NOTE: lf
the door has
not reached
the
desired limit
position
by more
than
30mm, it
is recommended
that
the
green
limits
cam
be adjusted
again
before
the
green
fine
adjustment screw is adjusted.
FIG,
11
OR
RE-EN6A6E
FIG.
12
^NIICLEXVISE
rO @EN @E
cL&xvtsE
ro @N
LEss
IOIAIE
6FEEN
'N
@Hp
F1G,
13