Automation Direct ATLAS ATM1900T Manuale di installazione rapida - Pagina 2
Sfoglia online o scarica il pdf Manuale di installazione rapida per Monitor Automation Direct ATLAS ATM1900T. Automation Direct ATLAS ATM1900T 4. Industrial flat panel pc monitor
Stampa la pagina2. Install Monitor through Enclosure Door or Wall
• The monitor must be installed on a flat surface of a NEMA type 1, 4, 4X
or 12 enclosure.
• Use dimensions as shown in the diagram below to provide a
rectangular mounting cutout in an approved NEMA 4/12 enclosure's
door or wall.
• Mount the monitor through the enclosure cutout, install and tighten (14)
mounting clips to a torque of 8.0 inch-pounds as shown in the diagram
to the right.
Cutout Dimensions:
A
B
Model
12.00"
15.00"
ATM1500/ATM1500T
(304.8 mm)
(381.0 mm)
13.70"
16.35"
ATM1700/ATM1700T
(348.0 mm)
(415.3 mm)
14.90"
17.75"
ATM1900/ATM1900T
(378.5 mm)
(450.9 mm)
W
: An operating temperature of 0 to 50 °C (32 to 122 °F)
ARNING
ambient termperature inside the enclosure needs to be maintained
for proper operation of the monitor.
Warning: Suitable for use in Class 1, Division 2 Groups A, B, C,
and D; Class 2 Division 2 Groups F and G, Class III hazardous
locations, or nonhazardous locations only.
3. Connect DVI or VGA Video Cable between Monitor & PC
• Connect the included 10' VGA video cable from the video connector on
the monitor to the video output connector on the host PC being used
with the monitor or use a digital DVI cable (sold separately).
• If using a DVI cable, input selection must be changed to DVI by pushing
the UP button on the rear of the monitor.
N
: T
15"
OTE
HE
MONITOR WILL PRODUCE THE BEST IMAGE QUALITY IF
PC
THE
IS SET FOR A
.
VIDEO MODE
N
: T
17"
OTE
HE
AND
PC
QUALITY IF THE
IS SET FOR A
75 H
.
OR
Z
VIDEO MODE
4. Connect USB or Serial Cable between Monitor & PC
• Applies to touch screen version only.
• Use either the included 10' RS-232 Serial touch screen cable or the 10'
USB touch screen cable from the appropriate connector on the monitor
to the appropriate connector on the host computer; do not connect
both.
• If using the USB cable, secure the cable using the included USB
retention bracket and screw; consult the Hardware User's Guide,
ATM-USER, on the supplied Documentation and Driver CD for details.
N
: W
OTE
HEN USING THE
USB
OF THE
RETENTION BRACKET IS REQUIRED FOR HAZARDOUS LOCA
TIONS AND HIGHLY RECOMMENDED FOR NONHAZARDOUS LOCATIONS
A
CUTOUT
B
1024
768
@
60, 70
X
PIXELS
EITHER
19"
MONITORS WILL PRODUCE THE BEST IMAGE
1280
1024
@
X
PIXELS
.
USB
TOUCHSCREEN CONNECTION
Mounting Clip Installation:
CUT AWAY
VIEW
W
ARNING
mounting clips.
Cable Connections:
75 H
.
OR
Z
60,
EITHER
W
ARNING
USB ports unless the power has been switched off or the area is
known to be non-hazardous.
A
VERTISSEMENT
le ports USB á moins que l'alimentation á été coupée ou si la zone
n'est pas hazardeuse.
A
DVERTENCIA
puertos USB a menos que la computadora se encuentre apagada o
el área se considere no peligrosa.
W
ARNUNG
,
THE USE
trennen, wenn keine spannung anliegt oder der Bereich nicht
-
explosiongefährdet ist.
.
N
: T
OTE
O
SERIAL TOUCHSCREEN CABLES ASSURE THAT THE THUMBSCREWS ARE
SUFFICIENTLY TIGHT
2
MAXIMUM ALLOWABLE
PANEL THICKNESS
: Damage can occur by applying excessive torque to the
WARNING
Touch Screen is still
active while display
power is off
DISPLAY POWER
VIDEO CABLE *
TOUCH SCREEN
CABLES *
- E
H
- Do not connect or disconnect the
XPLOSION
AZARD
- R
'
- Ne pas brancher ou débrancher
ISQUE D
EXPLOSION
- P
- No conecte o desconecte los
ELIGRO DE EXPLOSIÓN
- E
- USB-Ports nur anschließen oder
XPLOSIONSGEFAHR
P
REVENT INADVERTANT DISCONNECTION OF VIDEO AND
.
* NOTE: USE ONE OR THE
OTHER, NOT BOTH.
/
OR