Automation Direct ATLAS ATM1900T Quick Installation Manual - Page 2
Browse online or download pdf Quick Installation Manual for Monitor Automation Direct ATLAS ATM1900T. Automation Direct ATLAS ATM1900T 4 pages. Industrial flat panel pc monitor
Print Page2. Install Monitor through Enclosure Door or Wall
• The monitor must be installed on a flat surface of a NEMA type 1, 4, 4X
or 12 enclosure.
• Use dimensions as shown in the diagram below to provide a
rectangular mounting cutout in an approved NEMA 4/12 enclosure's
door or wall.
• Mount the monitor through the enclosure cutout, install and tighten (14)
mounting clips to a torque of 8.0 inch-pounds as shown in the diagram
to the right.
Cutout Dimensions:
A
B
Model
12.00"
15.00"
ATM1500/ATM1500T
(304.8 mm)
(381.0 mm)
13.70"
16.35"
ATM1700/ATM1700T
(348.0 mm)
(415.3 mm)
14.90"
17.75"
ATM1900/ATM1900T
(378.5 mm)
(450.9 mm)
W
: An operating temperature of 0 to 50 °C (32 to 122 °F)
ARNING
ambient termperature inside the enclosure needs to be maintained
for proper operation of the monitor.
Warning: Suitable for use in Class 1, Division 2 Groups A, B, C,
and D; Class 2 Division 2 Groups F and G, Class III hazardous
locations, or nonhazardous locations only.
3. Connect DVI or VGA Video Cable between Monitor & PC
• Connect the included 10' VGA video cable from the video connector on
the monitor to the video output connector on the host PC being used
with the monitor or use a digital DVI cable (sold separately).
• If using a DVI cable, input selection must be changed to DVI by pushing
the UP button on the rear of the monitor.
N
: T
15"
OTE
HE
MONITOR WILL PRODUCE THE BEST IMAGE QUALITY IF
PC
THE
IS SET FOR A
.
VIDEO MODE
N
: T
17"
OTE
HE
AND
PC
QUALITY IF THE
IS SET FOR A
75 H
.
OR
Z
VIDEO MODE
4. Connect USB or Serial Cable between Monitor & PC
• Applies to touch screen version only.
• Use either the included 10' RS-232 Serial touch screen cable or the 10'
USB touch screen cable from the appropriate connector on the monitor
to the appropriate connector on the host computer; do not connect
both.
• If using the USB cable, secure the cable using the included USB
retention bracket and screw; consult the Hardware User's Guide,
ATM-USER, on the supplied Documentation and Driver CD for details.
N
: W
OTE
HEN USING THE
USB
OF THE
RETENTION BRACKET IS REQUIRED FOR HAZARDOUS LOCA
TIONS AND HIGHLY RECOMMENDED FOR NONHAZARDOUS LOCATIONS
A
CUTOUT
B
1024
768
@
60, 70
X
PIXELS
EITHER
19"
MONITORS WILL PRODUCE THE BEST IMAGE
1280
1024
@
X
PIXELS
.
USB
TOUCHSCREEN CONNECTION
Mounting Clip Installation:
CUT AWAY
VIEW
W
ARNING
mounting clips.
Cable Connections:
75 H
.
OR
Z
60,
EITHER
W
ARNING
USB ports unless the power has been switched off or the area is
known to be non-hazardous.
A
VERTISSEMENT
le ports USB á moins que l'alimentation á été coupée ou si la zone
n'est pas hazardeuse.
A
DVERTENCIA
puertos USB a menos que la computadora se encuentre apagada o
el área se considere no peligrosa.
W
ARNUNG
,
THE USE
trennen, wenn keine spannung anliegt oder der Bereich nicht
-
explosiongefährdet ist.
.
N
: T
OTE
O
SERIAL TOUCHSCREEN CABLES ASSURE THAT THE THUMBSCREWS ARE
SUFFICIENTLY TIGHT
2
MAXIMUM ALLOWABLE
PANEL THICKNESS
: Damage can occur by applying excessive torque to the
WARNING
Touch Screen is still
active while display
power is off
DISPLAY POWER
VIDEO CABLE *
TOUCH SCREEN
CABLES *
- E
H
- Do not connect or disconnect the
XPLOSION
AZARD
- R
'
- Ne pas brancher ou débrancher
ISQUE D
EXPLOSION
- P
- No conecte o desconecte los
ELIGRO DE EXPLOSIÓN
- E
- USB-Ports nur anschließen oder
XPLOSIONSGEFAHR
P
REVENT INADVERTANT DISCONNECTION OF VIDEO AND
.
* NOTE: USE ONE OR THE
OTHER, NOT BOTH.
/
OR