ADEMCO 5817CB Manuale di installazione e configurazione

Sfoglia online o scarica il pdf Manuale di installazione e configurazione per Trasmettitore ADEMCO 5817CB. ADEMCO 5817CB 2. Wireless commercial / household transmitter
Anche per ADEMCO 5817CB: Istruzioni per l'installazione (4 pagine), Manuale di avvio rapido (2 pagine), Istruzioni per l'installazione (2 pagine), Manuale di installazione e configurazione (2 pagine)

Stampa la pagina

ADEMCO 5817CB

General Information

The 5817CB is a universal contact-monitoring transmitter that can be used with household and commercial fire and burglary-initiating devices such as

door/window contacts, motion and glassbreak detectors, sprinkler water flow switches, tamper switches, post indicator valves, manual pull stations,

and remote duct detectors. Upon activation, it emits an RF signal to a control panel that sends a burglary or fire alarm to a central station. The 5817CB

has three unique input loops (zones).

• The first loop (primary loop) is supervised and typically used for high-priority alarm reporting such as commercial fire or burglary. It requires a 470K

ohm end-of-line resistor (PN EOLR 470K) to be placed across the sensor.

• The second loop is the built-in, normally closed reed switch (used in conjunction with a magnet, as described below).

• The third loop is another normally closed household burglary loop. All three loops may be used.

• A fourth (automatically enrolled) loop contains two tamper switches to protect the 5817CB transmitter. A built-in cover tamper switch is activated

when the cover is removed. A unit tamper switch is activated if the unit is separated from its mounting plate.

Programming

The 5817CB has its own unique serial number permanently assigned during manufacture. You must "enroll" this transmitter serial number in the

control panel at some point prior to its usage in the alarm system. Refer to the control panel's installation instructions for specific programming

procedure.

Note: During programming of the control panel, program the 5817CB transmitter as Input Type "RF" (i.e., supervised RF) (mandatory for UL

installations).

Mounting

The 5817CB is supplied with a tamper switch hold-down (in the plastic parts bag) for use when the wall mounting plate is not needed. For proper

orientation of the unit in relation to its wall mounting plate and the loop wiring, read all of this section before installing the unit. Signal strength may vary

from location to location. Before mounting the transmitter permanently, conduct Go/No Go tests (see control's instructions) to verify adequate signal

strength from this location. When a satisfactory location is found, make note of the position of the unit on the wall, remove the battery and proceed

with installation.

Do not mount the transmitter on or near metal objects, as this may affect transmission range. It is also good practice to avoid

locating the transmitter near wiring such as AC, telephone, HVAC, computer data cables, etc.

The following mounting instructions assume that the unit will be

mounted as shown in the Figures. The unit may, however, be installed

in any direction, as long as the relationship of the unit to its mounting

plate (if used), is maintained.

The 5817CB is supplied with a tamper switch hold-down tab (connected

to the mounting plate as shown in Figure 1), for use when the wall

mounting plate is not needed. Remove the tab with diagonal cutting

pliers.

The mounting plate, installed as described below, enables easy removal

of the unit for servicing.

1. Remove the transmitter's cover by inserting the flat blade of a

small screwdriver into the pry-off slot at the bottom end of the unit

on the right side closest to the cover's decorative ribs and twisting.

2. Disengage the supplied mounting plate from the unit by

inserting the blade of a small screwdriver into the mounting plate

release hole (see Figure 3) and pushing the locking tab out (see

Figure 1). Slide the mounting plate downward along the case back.

Note: For this application, the alignment guide strip along one edge

of the mounting plate serves no function and may be broken away,

if desired.

3. If concealed wiring is to be used, feed the wires through the

concealed wiring entry hole at one corner of the mounting plate

(and/or case back). Surface wiring is discussed in Step 5 below).

4. Install the mounting plate, with its case-holding posts pointing up,

in the location determined. Use two flat head dry-wall screws.

Note: To ensure proper operation of the unit's back tamper (when it

is separated from the mounting plate), the screws must be anchored

to a wall stud or other solid wood material. If the mounting plate

will not be used, make note of the location of the tamper switch

hold-down as shown in Fig. 1 for the proper placing of the hold-

down tab in Fig. 2.

5. If surface wiring is to be used, remove the knockout slot in the

case back (located across from loop 3 terminal block). Surface

wiring should enter through this knocked out space provided. Do

not connect the wiring to the terminal block(s) yet.

6. Attach the case back to the mounting plate by sliding the keyhole

slots in the case back down onto the mounting plate's holding posts.

The locking tab will click as the case back locks in place.

To disengage the unit from an installed mounting plate, insert a

Wireless Commercial/Household Transmitter

Installation and Setup Guide

NOTE: For UL commercial and household fire installations, only one

initiating device may be connected to this transmitter. For UL commercial

burglary installations, multiple initiating devices may be used as long as the

devices all serve the same function, such as door/window contacts, motion

or glassbreak detectors. All initiating devices must be located within the

same room.

No more than one wire per terminal may be connected.

Use only 14-22AWG wire.

Figure 1. Mounting Plate

Figure 3. 5817CB Transmitter, Top Cover Removed

Figure 2. Case Back