ADEMCO 5808 Istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Allarme fumo ADEMCO 5808. ADEMCO 5808 4. Photoelectronic smoke/heat detector with built-in wireless transmitter
Anche per ADEMCO 5808: Istruzioni per l'installazione (5 pagine)
Stampa la pagina
ment. They can supply more detailed information about making your home
as free from fire hazards as possible and about planning for escape in case
of fire.
MOUNTING
First, determine the best location for the smoke detector; a location that
provides strong wireless transmission paths and proper smoke detec-
tion. A GOOD TRANSMISSION PATH MUST BE ESTABLISHED
FROM THE PROPOSED MOUNTING LOCATION BEFORE PERMA-
NENTLY INSTALLING THE DETECTOR. To check, perform the test
described in the TESTING TRANSMITTER SIGNAL section of this
manual. To mount the detector:
1. Once a suitable location has been determined, install the mounting
bracket on the ceiling or on the wall (if local ordinances permit). Use
the two screws and anchors provided.
2. Prior to mounting the detector to the mounting bracket, the system
must "enroll" the detector's ID. See the PROGRAMMING section for
the steps to follow.
3. Turn the detector in a clockwise direction in the mounting bracket
until it clicks into place.
4. Test the detector immediately after completing the installation (as
described in the TESTING section of this manual) and refer to the QED
control system's instructions for additional information concerning the
use of wireless smoke detectors.
TAMPER SLOT
(DEPRESS TAB
TO REMOVE
DETECTOR)
Figure 6. Detector Mounting Bracket
Figure 7. Mount Detector Across Ceiling Panel Support
DO NOT attach the detector to removable ceiling panels. Attach the
detector across panel support as shown in Figure 7.
TAMPER PROTECTION
This detector has a built-in tamper switch that will cause a CHECK signal
to be displayed at the console of the detector if it is removed from its
installation bracket. The mounting bracket can also be made tamperproof
by breaking off the smaller tab at the scribed line (see Figure 6), thus
preventing removal of the detector without a tool. To remove the
detector, use a small screwdriver to depress the tamperproof tab and
turn the detector counterclockwise.
TESTING
NOTE:
Before testing, notify the proper authorities that the smoke
detector system is undergoing maintenance and will tempo-
rarily be out of service. Disable the zone or system undergoing
maintenance to prevent unwanted alarms.
Detectors must be tested after installation and following periodic main-
tenance. The 5808 may be tested as follows:
A. TEST SWITCH
1. A recessed test switch is located on the detector housing.
2. Push and hold the recessed test switch with a 0.1" maximum
AD300-00-00
TAMPER RESISTANT TAB
(CUT OFF SMALL TAB TO
ACTIVATE TAMPER PROOF
FEATURE)
BRACKET INDICATES
POSITION OF LED WHEN
DETECTOR IS INSTALLED
A78-2333-03
A78-2620-00
CAUTION
diameter tool (an allen wrench or small screwdriver.)
3. The LED on the detector should blink once per second and the horn
should sound within 3 seconds.
B. TEST MODULE (Model No. MOD400R)
The MOD400R test module can be used with a DMM or analog
voltmeter to check the detector sensitivity as described in the test
module's manual.
C. SMOKE ENTRY TEST
Hold a smoldering punk stick or cotton wick at the side of the detector
and gently blow smoke through the detector until the unit alarms.
D. DIRECT HEAT METHOD (Hair dryer of 1000-1500 watts)
Direct the heat toward either side thermistor. Be sure to hold the heat
source about 12 inches from the detector to avoid damage to the
plastic. The detector will reset only after it has time to cool.
Smoke detection testing is recommended for verifying system protection
capability.
A detector that fails to activate with any of these tests should first be
cleaned as outlined in this manual's MAINTENANCE section. If the
detector still fails to activate, return for repair.
Notify the proper authorities that the system is back on line.
TESTING TRANSMITTER SIGNAL
NOTE: Remove battery tab before installation.
This test should be performed before installation to determine a strong
communication path with the QED control panel and after installation is
complete. Also, the owner/user should test the unit at least weekly.
1. Activate the wireless system's TEST mode from the console.
2. Depress and hold the smoke detector's TEST switch and the detector
should immediately transmit an alarm signal to the QED control panel.
The built-in horn will start to sound about 2.5 seconds after depressing
the button.
3. The wireless system's console should emit at least 3 audible sounds
when the alarm transmission is received and will display the transmit-
ting detector's ID number.
4. When the console has received the test signal, release the TEST
switch. The horn will immediately stop and a few seconds later the
detector's ID number will clear from the console display.
5. If the console does not respond as noted, check the polarity of the
batteries and be sure they are fresh. If this is an initial installation, try
moving the detector to another location that provides proper recep-
tion. Also be sure that the detector's ID has been "enrolled" by the QED
control panel (see PROGRAMMING). Then, repeat the test.
6. Turn off the system's TEST mode from the console (security code +
OFF).
MAINTENANCE
Figure 8. Removal of Cover and Screen for Cleaning
3
ARROW IS ALIGNED
WITH COVER REMOVAL
SLOT WHEN COVER
IS IN POSITION.
REPLACEMENT SCREEN,
ORDER PART NO. RS23
COVER
REMOVAL SLOT
A78-2335-01
I56-918-06