Dynamite Passport Manuale di istruzioni

Sfoglia online o scarica il pdf Manuale di istruzioni per Caricabatterie Dynamite Passport. Dynamite Passport 2. Duo 400w dual ac/dc touch charger

Stampa la pagina
Passport
Duo 400W Dual AC/DC Touch Charger
™
Instruction Manual | Bedienungsanleitung | Manuel d'utilisation | Manuale di Istruzioni
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit
horizonhobby.com and click on the support tab for this product.
MEANINg Of SPECIAl lANguAgE
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of
superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly
can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product
in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual
contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or
use, in order to operate correctly and avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for their safety.
ChArgINg WArNINgS
• Always monitor the charging area and have a fire extinguisher available at all
times.
WARNING: Failure to exercise caution while using this product and
comply with the following warnings could result in product malfunction,
• Always end the charging process if the battery becomes hot to the touch or
starts to change form (swell) during the charge process.
electrical issues, excessive heat, FIRE, and ultimately injury and property
damage.
• Always connect the charge cable to the charger first, then connect the battery
to avoid short circuit between the charge leads. Reverse the sequence when
• NEVER LEAVE ChARGING bATTERIEs UNATTENDED.
disconnecting.
• NEVER ChARGE bATTERIEs OVERNIGhT.
• Always connect the positive red leads (+) and negative black leads (–) correctly.
• Never attempt to charge dead, damaged or wet battery packs.
• Always disconnect the battery after charging, and let the charger cool between
• Never attempt to charge a battery pack containing different types of batteries.
charges.
• Never allow children under 14 years of age to charge battery packs.
• Always charge in a well-ventilated area.
• Never charge batteries in extremely hot or cold places or place in direct
• Always terminate all processes and contact Horizon Hobby if the product
sunlight.
malfunctions.
• Never charge a battery if the cable has been pinched or shorted.
WARNING: Never leave charger unattended, exceed maximum charge
• Never connect the charger if the power cable has been pinched or shorted.
rate, charge with non-approved batteries or charge batteries in the wrong
mode. Failure to comply may result in excessive heat, fire and serious
• Never connect the charger to an automobile 12V battery while the vehicle is
injury.
running.
• Never attempt to dismantle the charger or use a damaged charger.
CAUTION: Always ensure the battery you are charging meets the
• Never attach your charger to both an AC and a DC power source at the same
specifications of this charger and that the charger settings are correct.
time.
Not doing so can result in excessive heat and other related product
• Never connect the input jack (DC input) to AC power.
malfunctions, which can lead to user injury or property damage. Please
contact Horizon Hobby or an authorized retailer with compatibility
• Always use only rechargeable batteries designed for use with this type of
questions.
charger.
• Always inspect the battery before charging.
• Always keep the battery away from any material that could be affected by
heat.
VOlTAgE MuST BE SET TO ThE COrrECT VAluE BEfOrE ThE ChArgEr IS POWErED ON.
OPErATINg YOur ChArgEr
1 - SElf TEST AND PrOgrAM SElECT SCrEENS
When the charger is powered ON, there is a series of self tests and the screen will
show the charger brand name and model number.
D Y N C 3 0 0 5
USER_NAME
CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff disconnect the battery immediately and discontinue the
charge process as batteries can cause fire, collateral damage and injuries.
CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.
CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types
using the Lithium charge programs will damage the battery or the charger.
Only Li-Po is shown in the following three sections. Li-Ion/Li-Fe/Li-hV menus differ ONLY in Cell and Pack Voltage values.
2 - lIThIuM (lI-PO/lI-fE/lI-ION/lI-hV) ChArgINg
1. Connect the JST_XH balance adapter to the balance Circuit Adapter board
12. Press Unit to see the voltages for each cell. Press back to return to the
Connector (6).
charging screen.
2. Connect the battery connector to the device connector.
DATA LiPo–CELLS
3. Connect the balance connector of the battery to the JST_XH balance adapter.
4. Press the Left and Right Arrows on the LCD Touch screen to scroll through
the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe/Li-HV.
Program select=LiPo
4.08 4.07 4.06 0.00 0.00 0.00
LiPo
13. Press REs. to see the cell resistance screen. Press back to return to the
voltage screen.
– Resistance –
CHG
DCHG
STOR
Main:320MΩ
5. Press ChG.
1> 114MΩ
LiPo CHARGE
2> 104 MΩ
Pack.Volt.
:
11.1V/3S
3> 100 MΩ
Capacity
:
2100mAh
4> -- MΩ
Current
:
2.1A
End Cell Volt
:
4.20V
14. Press Graph to see the battery voltage graph. Press back to return to the
Press&Hold
:
CHARGE
charging screen.
BACK
SELECT
Data LiPo = Graph
6. Press a parameter to highlight that parameter.
7. Press the Up and Down Arrows to edit the parameter.
8. Press select to save the parameter.
9. Once the parameters are at the desired settings, press and hold ChARGE.
8.03V
000:34S
10. The charger will check the battery and charger settings and charging will begin.
The charger will beep and display the following screen:
15. Press sTOP at any time to stop charging.
16. When charging is complete, the charger will sound a series of beeps and
LiPo CHG
000:11S
display the following screen:
Capacity
:
11mAh
Current
:
4.0A
NiMH DONE
Voltage
:
8.00V
Input Volt
:
Resistance
:
392mΩ
Delta Peak
:
Peak Temp.
:
No sens
Int Temp.
:
STOP
Unit
Graph
Safety Timer
:
Capacity Lim. :
11. Press the arrow in the top right of the LCD Touch screen to see the rest of
BACK
Cycle
the Charging information.
LiPo CHG
010:30S
Input Volt
:
12.22V
17. Press the arrow in the top right of the LCD Touch screen to see the rest of
End Volt.
:
12.60V
the Charging information.
Int Temp
:
21ºC
LiPo DONE
Safety Timer
:
240min
Capacity Lim
:
2100mAh
Input Volt
:
End Volt.
:
STOP
Unit
Graph
Int Temp
:
Safety Timer
:
Capacity Lim
:
STOP
Unit
18. Disconnect the battery from the charger.
TABlE Of CONTENTS
1 - Self Test and Program Select Screens
8 - Pb Charging
2 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Charging
9 - Pb Discharging
2A - Lithium High Voltage
10 - Setup
3 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Discharging
11 - View
4 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Storage Charging
12 - Balance
5 - Nickel (Ni-MH/Ni-Cd) Charging
13 - Memory
6 - Nickel Discharging
14 - USB Device Charging
7 - Nickel Cycle Charging
15 - Troubleshooting
gETTINg STArTED
INCluDED ITEMS
Using an AC Power source:
(2) Banana plug to EC3™ battery connector (DYNC0066)
1. Ensure the charger is powered OFF.
AC power cord (one region—US, EU, AU or UK)
2. Connect the AC power cord (D) to the AC power source.
(2) JST_XH balance adapter (DYN5032)
3. Power ON the charger with the Power Switch (A).
4. When the charger is powered ON, a message will appear on the LCD Touch
screens (E,F).
OPTIONAl ITEMS
Using a DC Power source:
DC power cord (DYNC1103)
1.
Connect the DC power cord to the charger DC Power Input Port (C)
Banana to Traxxas® insulated charge adapter: male (DYNC0054)
2.
Connect the DC alligator clips to the DC power source.
Charger lead with receiver connector (DYNC0033)
Power ON the charger with the Power Switch (A).
3.
Banana to Deans insulated charge adapter: male (DYNC0053)
4.
When the charger is powered ON, a message will appear on the LCD Touch
screens (E,F).
LiPo Charge Protection Bag, Small (DYN1400)
LiPo Charge Protection Bag, Large (DYN1405)
Connecting the battery to the Charger:
Temperature Sensor (DYN5033)
CAUTION: Always power ON the charger before connecting a battery, or
damage to the charger and the battery can result.
SPECIfICATIONS
1.
With charger powered on, select charging settings.
Input Voltage 100-240V AC; 11-18V DC
2.
Connect the battery to the charger.
Charging Capability 1–6S Li-Po/Li-Ion/Li-Fe;
3.
Start battery charging.
1–10C Ni-Cd/Ni-MH; 2–24V Pb
CAUTION: Before charging, always ensure you have chosen the correct
Battery Capacities 50–10000 mAh
battery chemistry type for the battery you are charging.
Charge Current 0.01–10.0A (in 0.1A increments/200W max per channel)
PrOgrAMMINg quICk guIDE
Discharge Current 0.01–5A (in 0.1A increments/200W max per channel)
Operating Temperature 0ºC to + 40ºC
1. Press the Left and Right Arrows on the LCD Touch screen to scroll through
the main menu screens.
Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV
2. Press the action at the bottom of the LCD Touch screen to enter that menu.
Protection Short-circuit, over-current, reverse polarity, low input
3. Press a parameter to highlight that parameter.
voltage, over-temperature
4. Press the Up and Down Arrows to edit the parameter.
5. Press select to save the parameter.
6. If there is more than one screen of parameters, press the top right corner of the
LCD Touch screen to scroll through the parameter screens.
7. Press back to return to the main menu screens.
2A- lIThIuM hIgh VOlTAgE
CAUTION: Only use 4.35V capable Li-Po batteries when using the Li-HV charge mode. Charging other Li-Po batteries in this mode can lead to property damage,
fire, or serious injury.
1. Press the Left and Right Arrows on the LCD Touch screen to scroll through
the main menu screens until you reach Program Select=Li-HV.
Program select=LiHV
LiHV
CHG
DCHG
STOR
4. Press select to continue to charging.
5. Follow Lithium (Li-Po/Li-Fe/Li-Ion/LI-HV) Charging, Dishcharging and Storage
2. Press ChG.
insturctions
3. The following WARNING screen appears. You must be sure you are using
6. Press back to exit warning and choose another charging method.
High Voltage cells capable of being charged to 4.35 Volts.
3 - lIThIuM DISChArgINg
1.
Connect the JST_XH balance adapter to the balance Circuit Adapter
12. Press Unit to see the voltages for each cell. Press back to return to the
board Connector (6).
discharging screen.
2.
Connect the battery connector to the device connector.
BACK RES.
3.
Connect the balance connector of the battery to the JST_XH balance adapter.
4.
Press the Left and Right Arrows on the LCD Touch screen to scroll
through the main menu screens until you reach Program Select=Li-Po/Li-Ion/
Li-Fe/Li-HV.
Program select=LiPo
LiPo
13. Press REs. to see the cell resistance screen. Press back to return to the
voltage screen.
BACK
CHG
DCHG
STOR
5> -- MΩ
5. Press DChG.
6> -- MΩ
7> -- MΩ
LiPo DISCHARGE
8> -- MΩ
Pack.Volt.
:
11.1V/3S
Capacity
:
2100mAh
14. Press Graph to see the battery voltage graph. Press back to return to the
Current
:
2.1A
discharging screen.
End Cell Volt
:
3.80V
Press&Hold
:
DISCHRG
BACK
BACK
SELECT
6. Press a parameter to highlight that parameter.
7. Press the Up and Down Arrows to edit the parameter.
8. Press select to save the parameter.
9. Once the parameters are at the desired settings, press and hold DIsChRG.
15. Press sTOP at any time to stop discharging.
10. The charger will check the battery and charger settings and discharging will
16. When discharging is complete, the charger will sound a series of beeps and
begin. The charger will beep and display the following screen:
display the following screen:
LiPo DCHG
000:30S
001:15S
Capacity
:
13mAh
14.8?V
Current
:
1.4A
8mV/C
Voltage
:
11.39V
60F
Resistance
:
369mΩ
240min
Peak Temp.
:
No sens
3300mAh
STOP
Unit
Graph
Graph
11. Press the arrow in the top right of the LCD Touch screen to see the rest of
17. Press the arrow in the top right of the LCD Touch screen to see the rest of
the Discharging information.
the Charging information.
010:30S
12.22V
LiPo DONE
000:30S
12.60V
Input Volt
:
12.25V
21ºC
End Volt.
:
11.40V
240min
Int Temp
:
20ºC
2100mAh
Safety Timer
:
240min
Capacity Lim
:
2100mAh
Graph
STOP
Unit
Graph
18. Disconnect the battery from the charger.
A. Power Switch
b. AC Power Input Port
C. DC Power Input Port
D. AC Power Cord
E.
Charger 1- LCD Screen
F.
Charger 2- LCD Screen
G. Charger 1- Power Output Ports
h. Charger 1- Balance Board Port
I.
Charger 1- Temperature Sensor Port
J.
Charger 1- Micro USB Port
(Software updates ONLY; do not use for charging)
K. 2.1A USB Power Output Port
L.
Charger 2- Micro USB Port
(Software updates ONLY; do not use for charging)
M. Charger 2- Temperature Sensor Port
N. Charger 2- Balance Board Port
O. Charger 2- Power Output Ports
WARNING!
Battery must be 4.35
V/Cell compatible. If
not property damage
fire or serious injury
could result.
4 - lIThIuM STOrAgE ChArgINg
BACK
SELECT
1.
Connect the JST_XH balance adapter to the balance Circuit Adapter
board Connector (6).
2.
Connect the battery connector to the device connector.
3.
Connect the balance connector of the battery to the JST_XH balance adapter.
4.
Press the Left and Right Arrows on the LCD Touch screen to scroll
through the main menu screens until you reach Program Select=Li-Po/Li-Ion/
Li-Fe/Li-HV.
Program select=LiPo
LiPo
DATA LiPo–CELLS
CHG
DCHG
STOR
BACK RES.
5. Press sTOR.
LiPo STORAGE
Pack.Volt.
:
11.1V/3S
Capacity
:
2100mAh
3.80 3.80 3.80 0.00 0.00 0.00
Current
:
End Cell Volt
:
Press&Hold
:
– Resistance –
BACK
SELECT
BACK
Main:320MΩ
6. Press a parameter to highlight that parameter.
1> 114MΩ
5> -- MΩ
2> 104 MΩ
6> -- MΩ
7. Press the Up and Down Arrows to edit the parameter.
3> 100 MΩ
7> -- MΩ
8. Press select to save the parameter.
4> -- MΩ
8> -- MΩ
9. Once the parameters are at the desired settings, press and hold sTORE.
10. The charger will check the battery and charger settings and storage charging
will begin. The charger will beep and display the following screen:
Data LiPo = Graph
BACK
LiPo STORE
000:11S
Capacity
:
Current
:
Voltage
:
Resistance
:
Peak Temp.
:
No sens
7.91V
001:25S
STOP
Unit
Graph
11. Press the arrow in the top right of the LCD Touch screen to see the rest of
the storage Charging information.
LiPo DONE
000:30S
LiPo STORE
010:30S
Capacity
:
13mAh
Input Volt
:
12.22V
Current
:
1.4A
End Volt.
:
12.60V
Voltage
:
11.39V
Int Temp
:
Resistance
:
369mΩ
Safety Timer
:
240min
Peak Temp.
:
No sens
Capacity Lim
:
2100mAh
STOP
Unit
Graph
STOP
Unit
Graph
LiPo DONE
010:30S
Input Volt
:
12.22V
End Volt.
:
12.60V
Int Temp
:
21ºC
Safety Timer
:
240min
Capacity Lim
:
2100mAh
STOP
Unit
Graph
Not to scale.
Not all wiring shown.
Not all connectors shown.
D
E
F
A
B
C
CAUTION: The nickel charge program menus are to be used ONLY for the charging and discharging of nickel battery packs. Charging other battery types using
12. Press Unit to see the voltages for each cell. Press back to return to the
the nickel charge programs will damage the battery or the charger.
storage charging screen.
DATA LiPo–CELLS
BACK RES.
5 - NICkEl (NI-Mh/NI-CD) ChArgINg
1. Connect the battery connector to the device connector.
2. Press the Left and Right Arrows on the LCD Touch screen to scroll through
the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.
3.80 3.80 3.80 0.00 0.00 0.00
Program select=NiMH
13. Press Graph to see the battery voltage graph. Press back to return to the
storage charging screen.
Data LiPo = Graph
BACK
CHG
3. Press ChG.
NiMH CHARGE
Capacity
8.03V
000:34S
Current
CHG Mode
Delta Peak
2.1A
Press&Hold
3.80V
14. Press sTOP at any time to stop charging.
STORE
BACK
15. When charging is complete, the charger will sound a series of beeps and
display the following screen:
4. Press a parameter to highlight that parameter.
LiPo DONE
000:11S
5. Press the Up and Down Arrows to edit the parameter.
Capacity
:
4mAh
6. Press select to save the parameter.
Current
:
2.0A
Voltage
:
11.8V
7. Once the parameters are at the desired settings, press and hold ChARGE.
Resistance
:
375mΩ
8. The charger will check the battery and charger settings and charging will begin.
Peak Temp.
:
No sens
The charger will beep and display the following screen:
STOP
Unit
Graph
NiMH CHG
Capacity
Current
16. Press the arrow in the top right of the LCD Touch screen to see the rest of
Voltage
the Charging information.
Resistance
4mAh
Peak Temp.
2.0A
LiPo DONE
010:30S
STOP
11.8V
Input Volt
:
12.22V
375mΩ
End Volt.
:
12.60V
9. Press the arrow in the top right of the LCD Touch screen to see the rest of
Int Temp
:
21ºC
the Charging information.
Safety Timer
:
240min
Capacity Lim
:
2100mAh
NiMH CHG
STOP
Unit
Graph
Input Volt
Delta Peak
Int Temp
Safety Timer
Capacity Limit :
17. Disconnect the battery from the charger.
STOP
21ºC
G
H
I
J
K
L M
N
O
Only Ni-Mh is shown in the following three sections.
10. Press Graph to see the battery voltage graph. Press back to return to the
charging screen.
Data NiMH = Graph
BACK
N i M H
8.03V
000:28S
DCHG
CYCLE
11. Press sTOP at any time to stop charging.
12. When charging is complete, the charger will sound a series of beeps and
display the following screen:
:
50mAh
NiMH DONE
001:15S
:
0.1A
Capacity
:
53mAh
:
Man
Current
:
0.0A
:
5m V/C
Voltage
:
8.16V
:
CHARGE
Resistance
:
53mΩ
SELECT
Peak Temp.
:
No sens
BACK
Cycle
Graph
13. Press the arrow in the top right of the LCD Touch screen to see the rest of
the Charging information.
NiMH DONE
000:09S
Input Volt
:
12.24V
Delta Peak
:
1.8A
000:09S
Int Temp
:
21ºC
:
2mAh
Safety Timer
:
240min
:
1.8A
Capacity Limit :
2100mAh
:
7.98V
:
****mΩ
STOP
Graph
:
No sens
Graph
14. Disconnect the battery from the charger.
000:09S
:
12.24V
:
1.8A
:
21ºC
:
240min
2100mAh
Graph