Dynamite Passport Instrukcja obsługi

Przeglądaj online lub pobierz pdf Instrukcja obsługi dla Ładowarka Dynamite Passport. Dynamite Passport 2 stron. Duo 400w dual ac/dc touch charger

Drukuj stronę

Passport

Duo 400W Dual AC/DC Touch Charger

™

Instruction Manual | Bedienungsanleitung | Manuel d'utilisation | Manuale di Istruzioni

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit

horizonhobby.com and click on the support tab for this product.

MEANINg Of SPECIAl lANguAgE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of

superficial injury.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly

can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product

in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult

supervision. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual

contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or

use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years. This is not a toy.

NOTICE: This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for their safety.

ChArgINg WArNINgS

• Always monitor the charging area and have a fire extinguisher available at all

times.

WARNING: Failure to exercise caution while using this product and

comply with the following warnings could result in product malfunction,

• Always end the charging process if the battery becomes hot to the touch or

starts to change form (swell) during the charge process.

electrical issues, excessive heat, FIRE, and ultimately injury and property

damage.

• Always connect the charge cable to the charger first, then connect the battery

to avoid short circuit between the charge leads. Reverse the sequence when

• NEVER LEAVE ChARGING bATTERIEs UNATTENDED.

disconnecting.

• NEVER ChARGE bATTERIEs OVERNIGhT.

• Always connect the positive red leads (+) and negative black leads (–) correctly.

• Never attempt to charge dead, damaged or wet battery packs.

• Always disconnect the battery after charging, and let the charger cool between

• Never attempt to charge a battery pack containing different types of batteries.

charges.

• Never allow children under 14 years of age to charge battery packs.

• Always charge in a well-ventilated area.

• Never charge batteries in extremely hot or cold places or place in direct

• Always terminate all processes and contact Horizon Hobby if the product

sunlight.

malfunctions.

• Never charge a battery if the cable has been pinched or shorted.

WARNING: Never leave charger unattended, exceed maximum charge

• Never connect the charger if the power cable has been pinched or shorted.

rate, charge with non-approved batteries or charge batteries in the wrong

mode. Failure to comply may result in excessive heat, fire and serious

• Never connect the charger to an automobile 12V battery while the vehicle is

injury.

running.

• Never attempt to dismantle the charger or use a damaged charger.

CAUTION: Always ensure the battery you are charging meets the

• Never attach your charger to both an AC and a DC power source at the same

specifications of this charger and that the charger settings are correct.

time.

Not doing so can result in excessive heat and other related product

• Never connect the input jack (DC input) to AC power.

malfunctions, which can lead to user injury or property damage. Please

contact Horizon Hobby or an authorized retailer with compatibility

• Always use only rechargeable batteries designed for use with this type of

questions.

charger.

• Always inspect the battery before charging.

• Always keep the battery away from any material that could be affected by

heat.

VOlTAgE MuST BE SET TO ThE COrrECT VAluE BEfOrE ThE ChArgEr IS POWErED ON.

OPErATINg YOur ChArgEr

1 - SElf TEST AND PrOgrAM SElECT SCrEENS

When the charger is powered ON, there is a series of self tests and the screen will

show the charger brand name and model number.

D Y N C 3 0 0 5

USER_NAME

CAUTION: If at any time during the charge process the battery pack becomes hot or begins to puff disconnect the battery immediately and discontinue the

charge process as batteries can cause fire, collateral damage and injuries.

CAUTION: Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery.

CAUTION: The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs. Charging other battery types

using the Lithium charge programs will damage the battery or the charger.

Only Li-Po is shown in the following three sections. Li-Ion/Li-Fe/Li-hV menus differ ONLY in Cell and Pack Voltage values.

2 - lIThIuM (lI-PO/lI-fE/lI-ION/lI-hV) ChArgINg

1. Connect the JST_XH balance adapter to the balance Circuit Adapter board

12. Press Unit to see the voltages for each cell. Press back to return to the

Connector (6).

charging screen.

2. Connect the battery connector to the device connector.

DATA LiPo–CELLS

3. Connect the balance connector of the battery to the JST_XH balance adapter.

4. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens until you reach Program Select=Li-Po/Li-Ion/Li-Fe/Li-HV.

Program select=LiPo

4.08 4.07 4.06 0.00 0.00 0.00

LiPo

13. Press REs. to see the cell resistance screen. Press back to return to the

voltage screen.

– Resistance –

CHG

DCHG

STOR

Main:320MΩ

5. Press ChG.

1> 114MΩ

LiPo CHARGE

2> 104 MΩ

Pack.Volt.

11.1V/3S

3> 100 MΩ

Capacity

2100mAh

4> -- MΩ

Current

2.1A

End Cell Volt

4.20V

14. Press Graph to see the battery voltage graph. Press back to return to the

Press&Hold

CHARGE

charging screen.

BACK

SELECT

Data LiPo = Graph

6. Press a parameter to highlight that parameter.

7. Press the Up and Down Arrows to edit the parameter.

8. Press select to save the parameter.

9. Once the parameters are at the desired settings, press and hold ChARGE.

8.03V

000:34S

10. The charger will check the battery and charger settings and charging will begin.

The charger will beep and display the following screen:

15. Press sTOP at any time to stop charging.

16. When charging is complete, the charger will sound a series of beeps and

LiPo CHG

000:11S

display the following screen:

Capacity

11mAh

Current

4.0A

NiMH DONE

Voltage

8.00V

Input Volt

Resistance

392mΩ

Delta Peak

Peak Temp.

No sens

Int Temp.

STOP

Unit

Graph

Safety Timer

Capacity Lim. :

11. Press the arrow in the top right of the LCD Touch screen to see the rest of

BACK

Cycle

the Charging information.

LiPo CHG

010:30S

Input Volt

12.22V

17. Press the arrow in the top right of the LCD Touch screen to see the rest of

End Volt.

12.60V

the Charging information.

Int Temp

21ºC

LiPo DONE

Safety Timer

240min

Capacity Lim

2100mAh

Input Volt

End Volt.

STOP

Unit

Graph

Int Temp

Safety Timer

Capacity Lim

STOP

Unit

18. Disconnect the battery from the charger.

TABlE Of CONTENTS

1 - Self Test and Program Select Screens

8 - Pb Charging

2 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Charging

9 - Pb Discharging

2A - Lithium High Voltage

10 - Setup

3 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Discharging

11 - View

4 - Lithium (Li-Po/Li-Fe/Li-Ion/Li-HV) Storage Charging

12 - Balance

5 - Nickel (Ni-MH/Ni-Cd) Charging

13 - Memory

6 - Nickel Discharging

14 - USB Device Charging

7 - Nickel Cycle Charging

15 - Troubleshooting

gETTINg STArTED

INCluDED ITEMS

Using an AC Power source:

(2) Banana plug to EC3™ battery connector (DYNC0066)

1. Ensure the charger is powered OFF.

AC power cord (one region—US, EU, AU or UK)

2. Connect the AC power cord (D) to the AC power source.

(2) JST_XH balance adapter (DYN5032)

3. Power ON the charger with the Power Switch (A).

4. When the charger is powered ON, a message will appear on the LCD Touch

screens (E,F).

OPTIONAl ITEMS

Using a DC Power source:

DC power cord (DYNC1103)

Connect the DC power cord to the charger DC Power Input Port (C)

Banana to Traxxas® insulated charge adapter: male (DYNC0054)

Connect the DC alligator clips to the DC power source.

Charger lead with receiver connector (DYNC0033)

Power ON the charger with the Power Switch (A).

Banana to Deans insulated charge adapter: male (DYNC0053)

When the charger is powered ON, a message will appear on the LCD Touch

screens (E,F).

LiPo Charge Protection Bag, Small (DYN1400)

LiPo Charge Protection Bag, Large (DYN1405)

Connecting the battery to the Charger:

Temperature Sensor (DYN5033)

CAUTION: Always power ON the charger before connecting a battery, or

damage to the charger and the battery can result.

SPECIfICATIONS

With charger powered on, select charging settings.

Input Voltage 100-240V AC; 11-18V DC

Connect the battery to the charger.

Charging Capability 1–6S Li-Po/Li-Ion/Li-Fe;

Start battery charging.

1–10C Ni-Cd/Ni-MH; 2–24V Pb

CAUTION: Before charging, always ensure you have chosen the correct

Battery Capacities 50–10000 mAh

battery chemistry type for the battery you are charging.

Charge Current 0.01–10.0A (in 0.1A increments/200W max per channel)

PrOgrAMMINg quICk guIDE

Discharge Current 0.01–5A (in 0.1A increments/200W max per channel)

Operating Temperature 0ºC to + 40ºC

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens.

Charging Mode Ni-Cd/Ni-MH: Peak; Li-Po/Li-Ion/Li-Fe/Pb: CC/CV

2. Press the action at the bottom of the LCD Touch screen to enter that menu.

Protection Short-circuit, over-current, reverse polarity, low input

3. Press a parameter to highlight that parameter.

voltage, over-temperature

4. Press the Up and Down Arrows to edit the parameter.

5. Press select to save the parameter.

6. If there is more than one screen of parameters, press the top right corner of the

LCD Touch screen to scroll through the parameter screens.

7. Press back to return to the main menu screens.

2A- lIThIuM hIgh VOlTAgE

CAUTION: Only use 4.35V capable Li-Po batteries when using the Li-HV charge mode. Charging other Li-Po batteries in this mode can lead to property damage,

fire, or serious injury.

1. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens until you reach Program Select=Li-HV.

Program select=LiHV

LiHV

CHG

DCHG

STOR

4. Press select to continue to charging.

5. Follow Lithium (Li-Po/Li-Fe/Li-Ion/LI-HV) Charging, Dishcharging and Storage

2. Press ChG.

insturctions

3. The following WARNING screen appears. You must be sure you are using

6. Press back to exit warning and choose another charging method.

High Voltage cells capable of being charged to 4.35 Volts.

3 - lIThIuM DISChArgINg

Connect the JST_XH balance adapter to the balance Circuit Adapter

12. Press Unit to see the voltages for each cell. Press back to return to the

board Connector (6).

discharging screen.

Connect the battery connector to the device connector.

BACK RES.

Connect the balance connector of the battery to the JST_XH balance adapter.

Press the Left and Right Arrows on the LCD Touch screen to scroll

through the main menu screens until you reach Program Select=Li-Po/Li-Ion/

Li-Fe/Li-HV.

Program select=LiPo

LiPo

13. Press REs. to see the cell resistance screen. Press back to return to the

voltage screen.

BACK

CHG

DCHG

STOR

5> -- MΩ

5. Press DChG.

6> -- MΩ

7> -- MΩ

LiPo DISCHARGE

8> -- MΩ

Pack.Volt.

11.1V/3S

Capacity

2100mAh

14. Press Graph to see the battery voltage graph. Press back to return to the

Current

2.1A

discharging screen.

End Cell Volt

3.80V

Press&Hold

DISCHRG

BACK

SELECT

6. Press a parameter to highlight that parameter.

7. Press the Up and Down Arrows to edit the parameter.

8. Press select to save the parameter.

9. Once the parameters are at the desired settings, press and hold DIsChRG.

15. Press sTOP at any time to stop discharging.

10. The charger will check the battery and charger settings and discharging will

16. When discharging is complete, the charger will sound a series of beeps and

begin. The charger will beep and display the following screen:

display the following screen:

LiPo DCHG

000:30S

001:15S

Capacity

13mAh

14.8?V

Current

1.4A

8mV/C

Voltage

11.39V

60F

Resistance

369mΩ

240min

Peak Temp.

No sens

3300mAh

STOP

Unit

Graph

11. Press the arrow in the top right of the LCD Touch screen to see the rest of

17. Press the arrow in the top right of the LCD Touch screen to see the rest of

the Discharging information.

the Charging information.

010:30S

12.22V

LiPo DONE

000:30S

12.60V

Input Volt

12.25V

21ºC

End Volt.

11.40V

240min

Int Temp

20ºC

2100mAh

Safety Timer

240min

Capacity Lim

2100mAh

Graph

STOP

Unit

Graph

18. Disconnect the battery from the charger.

A. Power Switch

b. AC Power Input Port

C. DC Power Input Port

D. AC Power Cord

Charger 1- LCD Screen

Charger 2- LCD Screen

G. Charger 1- Power Output Ports

h. Charger 1- Balance Board Port

Charger 1- Temperature Sensor Port

Charger 1- Micro USB Port

(Software updates ONLY; do not use for charging)

K. 2.1A USB Power Output Port

Charger 2- Micro USB Port

(Software updates ONLY; do not use for charging)

M. Charger 2- Temperature Sensor Port

N. Charger 2- Balance Board Port

O. Charger 2- Power Output Ports

WARNING!

Battery must be 4.35

V/Cell compatible. If

not property damage

fire or serious injury

could result.

4 - lIThIuM STOrAgE ChArgINg

BACK

SELECT

Connect the JST_XH balance adapter to the balance Circuit Adapter

board Connector (6).

Connect the battery connector to the device connector.

Connect the balance connector of the battery to the JST_XH balance adapter.

Press the Left and Right Arrows on the LCD Touch screen to scroll

through the main menu screens until you reach Program Select=Li-Po/Li-Ion/

Li-Fe/Li-HV.

Program select=LiPo

LiPo

DATA LiPo–CELLS

CHG

DCHG

STOR

BACK RES.

5. Press sTOR.

LiPo STORAGE

Pack.Volt.

11.1V/3S

Capacity

2100mAh

3.80 3.80 3.80 0.00 0.00 0.00

Current

End Cell Volt

Press&Hold

– Resistance –

BACK

SELECT

BACK

Main:320MΩ

6. Press a parameter to highlight that parameter.

1> 114MΩ

5> -- MΩ

2> 104 MΩ

6> -- MΩ

7. Press the Up and Down Arrows to edit the parameter.

3> 100 MΩ

7> -- MΩ

8. Press select to save the parameter.

4> -- MΩ

8> -- MΩ

9. Once the parameters are at the desired settings, press and hold sTORE.

10. The charger will check the battery and charger settings and storage charging

will begin. The charger will beep and display the following screen:

Data LiPo = Graph

BACK

LiPo STORE

000:11S

Capacity

Current

Voltage

Resistance

Peak Temp.

No sens

7.91V

001:25S

STOP

Unit

Graph

11. Press the arrow in the top right of the LCD Touch screen to see the rest of

the storage Charging information.

LiPo DONE

000:30S

LiPo STORE

010:30S

Capacity

13mAh

Input Volt

12.22V

Current

1.4A

End Volt.

12.60V

Voltage

11.39V

Int Temp

Resistance

369mΩ

Safety Timer

240min

Peak Temp.

No sens

Capacity Lim

2100mAh

STOP

Unit

Graph

STOP

Unit

Graph

LiPo DONE

010:30S

Input Volt

12.22V

End Volt.

12.60V

Int Temp

21ºC

Safety Timer

240min

Capacity Lim

2100mAh

STOP

Unit

Graph

Not to scale.

Not all wiring shown.

Not all connectors shown.

CAUTION: The nickel charge program menus are to be used ONLY for the charging and discharging of nickel battery packs. Charging other battery types using

12. Press Unit to see the voltages for each cell. Press back to return to the

the nickel charge programs will damage the battery or the charger.

storage charging screen.

DATA LiPo–CELLS

BACK RES.

5 - NICkEl (NI-Mh/NI-CD) ChArgINg

1. Connect the battery connector to the device connector.

2. Press the Left and Right Arrows on the LCD Touch screen to scroll through

the main menu screens until you reach Program Select=Ni-MH/Ni-Cd.

3.80 3.80 3.80 0.00 0.00 0.00

Program select=NiMH

13. Press Graph to see the battery voltage graph. Press back to return to the

storage charging screen.

Data LiPo = Graph

BACK

CHG

3. Press ChG.

NiMH CHARGE

Capacity

8.03V

000:34S

Current

CHG Mode

Delta Peak

2.1A

Press&Hold

3.80V

14. Press sTOP at any time to stop charging.

STORE

BACK

15. When charging is complete, the charger will sound a series of beeps and

display the following screen:

4. Press a parameter to highlight that parameter.

LiPo DONE

000:11S

5. Press the Up and Down Arrows to edit the parameter.

Capacity

4mAh

6. Press select to save the parameter.

Current

2.0A

Voltage

11.8V

7. Once the parameters are at the desired settings, press and hold ChARGE.

Resistance

375mΩ

8. The charger will check the battery and charger settings and charging will begin.

Peak Temp.

No sens

The charger will beep and display the following screen:

STOP

Unit

Graph

NiMH CHG

Capacity

Current

16. Press the arrow in the top right of the LCD Touch screen to see the rest of

Voltage

the Charging information.

Resistance

4mAh

Peak Temp.

2.0A

LiPo DONE

010:30S

STOP

11.8V

Input Volt

12.22V

375mΩ

End Volt.

12.60V

9. Press the arrow in the top right of the LCD Touch screen to see the rest of

Int Temp

21ºC

the Charging information.

Safety Timer

240min

Capacity Lim

2100mAh

NiMH CHG

STOP

Unit

Graph

Input Volt

Delta Peak

Int Temp

Safety Timer

Capacity Limit :

17. Disconnect the battery from the charger.

STOP

21ºC

L M

Only Ni-Mh is shown in the following three sections.

10. Press Graph to see the battery voltage graph. Press back to return to the

charging screen.

Data NiMH = Graph

BACK

N i M H

8.03V

000:28S

DCHG

CYCLE

11. Press sTOP at any time to stop charging.

12. When charging is complete, the charger will sound a series of beeps and

display the following screen:

50mAh

NiMH DONE

001:15S

0.1A

Capacity

53mAh

Man

Current

0.0A

5m V/C

Voltage

8.16V

CHARGE

Resistance

53mΩ

SELECT

Peak Temp.

No sens

BACK

Cycle

Graph

13. Press the arrow in the top right of the LCD Touch screen to see the rest of

the Charging information.

NiMH DONE

000:09S

Input Volt

12.24V

Delta Peak

1.8A

000:09S

Int Temp

21ºC

2mAh

Safety Timer

240min

1.8A

Capacity Limit :

2100mAh

7.98V

****mΩ

STOP

Graph

No sens

Graph

14. Disconnect the battery from the charger.

000:09S

12.24V

1.8A

21ºC

240min

2100mAh

Graph