Autonics TN Series Manuale del prodotto - Pagina 2

Sfoglia online o scarica il pdf Manuale del prodotto per Controllore Autonics TN Series. Autonics TN Series 5. Two-degree-of-freedom pid temperature controllers
Anche per Autonics TN Series: Manuale del prodotto (6 pagine), Manuale di istruzioni (2 pagine)

Stampa la pagina

• Install a power switch or circuit breaker in the easily accessible place for supplying or

disconnecting the power.

• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature

controller.

• When changing the input sensor, turn off the power first before changing. After

changing the input sensor, modify the value of the corresponding parameter.

• Do not overlapping communication line and power line. Use twisted pair wire for

communication line and connect ferrite bead at each end of line to reduce the effect

of external noise.

• Make a required space around the unit for radiation of heat. For accurate temperature

measurement, warm up the unit over 20 min after turning on the power.

• Make sure that power supply voltage reaches to the rated voltage within 2 sec after

supplying power.

• Do not wire to terminals which are not used.

• This unit may be used in the following environments.

- Indoors (in the environment condition rated in 'Specifications')

- Altitude Max. 2,000 m

- Pollution degree 2

- Installation category II

Ordering Information

This is only for reference, the actual product does not support all combinations.

For selecting the specified model, follow the Autonics website .

T N ❶ - ❷ 4 ❸ ❹ ❺ - ❻ S - ❼

❶ Size

S: DIN W 48 × H 48 mm

H: DIN W 48 × H 96 mm

L: DIN W 96 × H 96 mm

❷ Control method

No mark: Fixed control

P: Program control

❸ Alarm outputs

2: Alarm 1 / 2

4: Alarm 1 / 2 / 3 / 4

6: Alarm 1 / 2 / 3 / 4 / 5 / 6

❹ Control output 1

R: Relay

S: SSR drive

C: Current or SSR drive

Manual

For proper use of the product, refer to the manuals and be sure to follow the safety

considerations in the manuals.

Download the manuals from the Autonics website.

Software

Download the installation file and the manuals from the Autonics website.

■ DAQMaster

DAQMaster is comprehensive device management program. It is available for

parameter setting, monitoring.

Product Components

• Product

• Bracket

Sold Separately

• Communication converter: SCM Series

• Terminal protection cover

❺ Control output 2

R: Relay

S: SSR drive

C: Current or SSR drive

❻ Communication

N: None

R: RS485

❼ Option input/output

Digital

Transmission

No.

CT input

input

output

006 0

008 2

009 3

014 3

026 0

031 0

035 6

• Instruction manual

• Current transformer (CT)

• Front cover

Specifications

Power supply

100 - 240 VACᜠ, 50/60 Hz ±10%

Power consumption

≤ 8 VA

Display type

11 segment, LCD type (operating value display part: 7 segment)

Sampling period

50 / 100 / 250 ms (parameter)

Input specification

Refer to 'Input Type and Using Range'

• 0.0-50.0 A (primary current measurement range)

• CT ratio: 1/1,000

• Measurement accuracy: ±5% F.S. ±1digit

Option

input

• Contact - ON: ≤ 2 kΩ, OFF: ≥ 90 kΩ

Digital

• Non contact - residual voltage ≤ 1.0 V, leakage current ≤ 0.1 mA

• Outflow current: ≈ 0.5 mA per input

Relay

250 VACᜠ 3A 1a

Control

SSR

12 VDCᜡ ±2 V, ≤ 20 mA

output

DC 0 - 20 mA or DC 4 - 20 mA (parameter), Load resistance: ≤

Current

500 Ω

Alarm

250 VACᜠ 3 A 1a

Option

DC 4 - 20 mA (load resistance: ≤ 500 Ω, output accuracy: ±0.3%

Transmission

output

F.S.)

Communication RS485

Type

ON/OFF, P, PI, PD, PID

Multi SV

≤ 4 SV

Control

Group PID

≤ 8 group

type

Zone PID

4 zones

ARW (Anti Reset

50 to 200 %

Windup)

Program

≤ 10 patterns

Program

Step

≤ 200 steps (1 pattern: ≤ 20 steps)

control

Setting type

Time setting

• Thermocouple, RTD: 1 to 100 (0.1 to 100.0) ℃/℉

Hysteresis

• Analog: 1 to 100 digit

Proportional band (P)

0.1 to 999.9 ℃ (0.1 to 999.9%)

Integral time (I)

0 to 9,999 sec

Derivative time (D)

0 to 9,999 sec

• Relay / SSRP output: 0.1 to 120.0 sec

Control cycle (T)

• Selectable current or SSR drive output: 1.0 to 120.0 sec

Manual reset

0.0 to 100.0%

Between the charging part and the case:

Dielectric strength

3,000 VACᜠ 50/60 Hz for 1 min

0.75 mm amplitude at frequency of 5 to 55 Hz (for 1 min) in each X,

Vibration

Y, Z direction for 2 hours

• OUT1/2: ≥ 5,000,000 operations

Mechanical

• AL1/2/3/4/5/6: ≥ 20,000,000 operations

Relay life

cycle

• OUT1/2: ≥ 200,000 operations

Electrical

• AL1/2/3/4/5/6: ≥ 100,000 operations

Insulation resistance

≥ 100 MΩ (500 VDCᜡ megger)

Double insulation or reinforced insulation (mark: ▱, dielectric

Insulation type

strength between the measuring input part and the power part:

3 kV)

±2 kV square shaped noise by noise simulator (pulse width: 1 ㎲)

Noise immunity

R-phase, S-phase

Memory retention

≈ 10 years (non-volatile semiconductor memory type)

Ambient temperature

-10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)

Ambient humidity

35 to 85%RH

Protection structure

IP65 (Front panel, IEC standards)

Loader port

• TNS: top side

Bracket

Accessory

• TNS: ≈ 128 g (≈ 156 g)

Unit weight (packaged)

• TNL: ≈ 301 g (≈ 443 g)

Approval

ᜢ ᜧ ᜣ

Communication Interface

■ RS485

Comm. protocol

Modbus RTU/ASCII, Sync-Master, PLC ladderless

Connection type

RS-485, RS-422A

Application standard

EIA RS485 compliance with

Maximum connection

32 units (address: 01 to 99)

Synchronous method

Asynchronous

Comm. Method

Two-wire half duplex

Comm. effective range

≤ 800 m

Comm. speed

≤ 115,200 bps

Response time

5 to 99 ms (default: 20 ms)

Start bit

1 bit (fixed)

Data bit

8 bit (fixed)

Parity bit

None (default), Odd, Even

Stop bit

1 bit, 2 bit (default)

EEPROM life cycle

≈ 1,000,000 operations (Erase / Write)

• 1 character of ModBus RTU is fixed at 11 bit.

• TNH, TNL: front side

• TNH: ≈ 184 g (≈ 286 g)