AUTOSCALER AW30C Manuale - Pagina 7

Sfoglia online o scarica il pdf Manuale per Convertitore multimediale AUTOSCALER AW30C. AUTOSCALER AW30C 14.

Stampa la pagina

FEATURES

The AUTOSCALER® is designed for Dental Prophylaxis Treatment when

used with the appropriate Cavitron® brand – Series: "P", "SLIMLINE"™,

"FSI"™ or "TFI"™ 25,000Hz series inserts*. If you have purchased the

AUTOSCALER® 30,000Hz model you must use the 30,000Hz frequency

inserts. Inserts are not interchangeable. The AUTOSCALER® is acceptable

for use in scaling and cleaning surfaces of teeth in conjunction with other

prophylactic measures.

This Build-In style AUTOSCALER® unit is NOT intended for user/owner

install. It requires a technician familiar with dental operatory Air and

Water circuitry. This product needs installation of the following for

proper operation:

1. The Handpiece Assembly. Routing of 18 gauge wires through the

dental operatory to the AUTOSCALER® console.

2. Water delivery/control for the unit. The AUTOSCALER® does not come

equipped with any water control devices/controllers, however proper

water flow is mandatory for the operation of this product. See oper-

ating instructions later in this booklet for proper operating parameters.

3. Power Control Pot. Routing of (2) 18 gauge wires through the dental

operatory to the AUTOSCALER® console.

4. An independent Air Source to activate the AUTOSCALER® supplied by

the dental operatory (i.e. independent air/water block with auto

holder). The air supply must relieve to zero pressure after each

depression of the main air rheostat.

AUTOSCALER® is a trade mark of South East Instruments, LLC.

Recommendations by the manufacturer contained within this instruction

booklet are suggestions only. Other options may be available or mandated

by the professional or regulating agencies.

The source of the air signal, water supply, and installation are not the

responsibility of South East Instruments, LLC. Any damage to the

AUTOSCALER®, PATIENTS or DENTAL OPERATORY resulting from improper

installation or configuration is the sole responsibility of the installing dealer

or technician. The AUTOSCALER® BUILD-IN Models AW25BI or AW30BI are

sold as component devices that require further installation by a party

appointed by the end user. If the installing technician or end user is in doubt

as to correct installation procedures they should stop immediately and call

South East Instruments, LLC for further instructions at (800) 648-9445 before

attempting to proceed with the installation.

*Cavitron®, SLIMLINE™, FSI™, and TFI™ are registered trade marks of Dentsply Sirona

BUILD-IN MODEL INSTALLATION GUIDE

This GUIDE is to assist the technician. Most dental chairs utilize similar

configurations. It is the responsibility of the technician to properly

install and confirm proper function with the particular chair

manufacturer configuration.

DO NOT attempt to install this device without an independent air/

water block with automatic handpiece holder. The technician must

be familiar with dental chair air water logic to correctly install this

device. Most installations convert the existing 3

high or low speed drill block for this purpose.

There MUST be (4) 18

GAUGE wires running from

the junction box,

THROUGH THE ARM to the

tray for handpiece and power

control connections.

The AUTOSCALER® (CONSOLE) is mounted under the chair or

(JUNCTION BOX). NOTE: If the AUTOSCALER® receives an air signal

from another source (i.e. high speed or low speed drill) it can damage

the device and the handpiece assembly.

WATER FLOW to the handpiece is received from the air/water block (NEEDLE

VALVE). When the main air rheostat is pressed, an air signal is sent to the

AUTOSCALER® console to (cavitate the insert) and the air/water block opens to

release water flow to the handpiece. Quickly adjust the water knob to get

water flowing.

or 4

air/water

The handpiece and

(POWER CONTROL)

are mounted on the (tray).

An (AUTOMATIC

HOLDER) must be used

for the Autoscaler®

handpiece.