Century Helicopter Products Hummingbird Elite 3D Pro Manuale di montaggio e istruzioni - Pagina 4

Sfoglia online o scarica il pdf Manuale di montaggio e istruzioni per Giocattolo Century Helicopter Products Hummingbird Elite 3D Pro. Century Helicopter Products Hummingbird Elite 3D Pro 12.
Anche per Century Helicopter Products Hummingbird Elite 3D Pro: Manuale di istruzioni (10 pagine)

Stampa la pagina

Century Helicopter Products Hummingbird Elite 3D Pro Manuale di montaggio e istruzioni

1. Specifications

Section 4: Tail Drive Assembly (Continued)

Bags Used:

CNE308, CNE309, CNE312, CNE216

Tail Boom/Drive II (4-1, 4-2, 4-3)

9) Slide one of the CNE213

Bearing

10) Open parts bag CNE305

CNE305 includes a bag with 3x

into a container or open the bag when it's ready to be use.

11) Get the

Small Beveled Gear

Tail Drive

Shaft. Make sure that the head is ﬂush with the tip of

Drive

Shaft. Place a small amount of locktite on the threads of the

Screw

to secure the

Small Beveled Gear

4-2).

12) Install the

Tail Drive Shaft

Boom

Bracket. Then insert the

Shaft. Use a small amount of locktite to secure the

Drive

eled Gear

in place by using the supplied

13) Using parts bag CNE308

mounts over the

Tail Boom

the screws in CNE308 at this time.

Section 5: Landing Gear & Tail Supports

Bags Used:

CNE326, CNE310, CNE317, CNE316

Landing gear assembly (5-1, 5-2, 5-3)

14) Open CNE326

Landing Gear

inside of the curved portion of the

holes in these posts. When you attach the

all of the holes are pointing to the rear.

15) Use the supplied

M2x11.5 Machine Screws

of the

Landing Struts

to the

the

Rear Lower

Bracket.

16) Insert one

Pushrod Guide

ﬁns bag. Install the

Horizontal Fin

Push Rod

Guides.

17) (This step is related to the assembly in this section but cannot be completed

until 10-2 has been completed). Insert the carbon ﬁber

the

Mounting Posts

and in to

plied

M2x8 Machine Screw

18) Use the

Rudder Pushrod

in the

Push Rod Guides

Put our assemblies to the side for now and we will get back to it later.

5-2

M2x8 Machine

Horizontal ﬁn

Screw #CNE317

#CNE317

over the

Tail Drive

Shaft.

Tail Drive Gear

Set.

M2x2 Set

Screws, put these screws

and insert it into the rear section of the

on the

Tail Drive Shaft

into the

Tail Boom

and through the

Large Beveled Gear

onto the

M2x2 Set

Screw.

Rear Rudder Servo

Mounts, insert both

(refer to 4-3 for direction).

Set. Note that

there are mounting posts on the

Landing

Struts. Also notice that there are

Landing Gear

found in CNE310 to mount one

Radio

Tray. The other

Landing Strut

ﬁrst and then the

Horizontal Fin

onto the CNE316

Tail Boom

Horizontal Fin

Mounting

Posts. Use the sup-

to secure the

Horizontal

Fin.

from bag CNE316 connecting it to the indentations

Pushrod Guide

#CNE316

Tail Boom

#CNE316

4-1

Tail Boom #CNE316

(Rear side with round holes)

4-2

Tail

Set

(see

Tail

M2x2 Set

Screw

Large Bev-

#CNE305

4-3

Do not tighten

Tail boom

#CNE308 Rear

#CNE316

Rudder Servo

Mounts

Set, make sure that

connects to

from CNE317 3D

between the

Mounting Posts

(For boom supports

Tail Boom Support

pointing rearward)

Tail Boom Supports

#CNE317

5-3

Tail Drive Shaft

#CNE315

Bearing

#CNE213

Small Beveled

Tail Drive Gear

#CNE305

Large Beveled

Tail Drive Gear

#CNE305

5-1

Rear Lower

Bracket

#CNE310

M2x11.5 Machine

Screws

#CNE326

(Landing Gear)

Rudder Pushrod

#CNE316

Note: Only Do step (5-3)

after completing (10-2)

M2x2 Set Screw

#CNE305

Tail Drive Shaft (must sit

ﬂush with the large beveled

gear) #CNE315

Radio Tray

#CNE310

Landing Struts

(Plastic)

#CNE326

Landing Skids

(Aluminum)

#CNE326

Pushrod Guide

#CNE316

Horizontal Fin and clamp

with Mounting Posts for

boom supports #CNE317