KitchenAid Superba KDS20A Manuale di istruzioni per l'installazione - Pagina 2

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Lavastoviglie KitchenAid Superba KDS20A. KitchenAid Superba KDS20A 6. Built-in

Stampa la pagina

IMPORTANT:

Read

Before

Installing

to Save Time,

Work,

assure

proper

performance,

and owner's

warranty

protection.

CABINETRY

Opening

for

dishwasher

should

be 24"

wide

approximately

34-l/2"

high. Remove all obstructions

at the upper rear of the opening-see

Step 1 below.

ELECTRICAL

SPECIFICATIONS

Voltage & Frequency

115 volts-60

hertz

Operating

load

13.5 amperes

Maximum

Fuse Size

15 amperes

Wiring

must conform

to local code and/or

National

Electrical

Code.

PLUMBING

SPECIFICATIONS

Plumbing

must conform

to local code. Use l/2"

O.D.

copper

tube

for

water

line.

Dishwasher

has 3/8"

N.P.T.F.

internal

thread at valve. A 90" compression

ell (not furnished)

should

be used to connect

tubing

to valve, Water flow pressure at dishwasher

to be 20

P.S.I. to 120 P.S.I. Water temperature

at dishwasher

should

be 120°F.

higher.

Drain

size requires

minimum

5/8"

O.D. copper tubing

without

air gap.

Drain

line requires

min. g/16"

I.D. tubing

with

air

gap, not furnished.

CAUTION:

Avoid

getting

joint

compound

inside

new joints.

Hot water

fill

line must be flushed

foreign

matter

before connection

to dishwasher

fill

valve. A hand shut off valve (not furnished)

should be

located

in an easily

accessible area adjacent

to the

dishwasher.

INSTALLATION

INSTRUCTIONS

KDS-20A

dishwasher

is equipped

with

reversible

front

panels in order to accom-

modate

a variety

of colors. Custom wood panels may also be used. Consult

the

Use and Care Guide for instructions

on changing front panels.

FIG. 1

The lower front

panel must be removed to enable plumbing

and electrical

con-

nections

to be made. To remove lower panel, take out two screws (C) and lock

washer (D). With

index fingers,

push support

tabs (B) up, and pull bottom

lower panel outward

to clear tabs of kickboard.

Slide lower panel down until side

flanges

are clear of evaporation

channel

support

(A). Reverse procedure

when

replacing

lower panel.

PRELIMINARY

ROUGH-IN

CABINET

OPENING

SHADED AREA SHOULD

BE FREE

of ALL PLUMBIND

AND ELECTRICAL CONNMOM

For dishwasher

to be flush with adjacent cabinets, there must be a minimum

of 24-l/4"

under counter

cabinet

depth available

for installation.

To estab-

lish a reference

line for purposes of providing

plumbing

and electrical

con-

nections

to the dishwasher,

measure 21"

from

the wall. (This is the front

edge of dishwasher

kick panel. There is a 3" toe space from the front of the

kick panel to the front

edge of the dishwasher

with

a standard

metal front

panel.) Cabinets 23-l/2"

to 23-5/8"

deep from wall to front of cabinet may

be accommodated

by removing

dry or plaster wall, baseboard and quarter

round directly

behind the dishwasher.

NOTE:

For corner

installation,

allow

2" clearance

for adjacent

cabinet.

CAUTION:

Make sure dishwasher

is not installed

under a surface burner or

warming

plate where the heat would

damage the water supply tubing.

If the

rear cross channel interferes

with the plumbing

and/or electrical

connections,

it may be relocated

as shown in Fig. 3 to create more clearance between the

cross channel and the floor.

-2-

FIG. 2