KitchenAid Superba KDS20A Handleiding voor installatie-instructies - Pagina 2

Blader online of download pdf Handleiding voor installatie-instructies voor {categorie_naam} KitchenAid Superba KDS20A. KitchenAid Superba KDS20A 6 pagina's. Built-in

IMPORTANT:
Read
Before
Installing
to Save Time,
Work,
assure
proper
performance,
and owner's
warranty
protection.
CABINETRY
Opening
for
dishwasher
should
be 24"
wide
by
approximately
34-l/2"
high. Remove all obstructions
at the upper rear of the opening-see
Step 1 below.
ELECTRICAL
SPECIFICATIONS
Voltage & Frequency
115 volts-60
hertz
Operating
load
13.5 amperes
Maximum
Fuse Size
15 amperes
Wiring
must conform
to local code and/or
National
Electrical
Code.
PLUMBING
SPECIFICATIONS
Plumbing
must conform
to local code. Use l/2"
O.D.
copper
tube
for
water
line.
Dishwasher
has 3/8"
N.P.T.F.
internal
thread at valve. A 90" compression
ell (not furnished)
should
be used to connect
tubing
to valve, Water flow pressure at dishwasher
to be 20
P.S.I. to 120 P.S.I. Water temperature
at dishwasher
should
be 120°F.
or
higher.
Drain
size requires
minimum
5/8"
O.D. copper tubing
without
air gap.
Drain
line requires
min. g/16"
I.D. tubing
with
air
gap, not furnished.
CAUTION:
Avoid
getting
joint
compound
inside
new joints.
Hot water
fill
line must be flushed
of
foreign
matter
before connection
to dishwasher
fill
valve. A hand shut off valve (not furnished)
should be
located
in an easily
accessible area adjacent
to the
dishwasher.
INSTALLATION
INSTRUCTIONS
n
KDS-20A
dishwasher
is equipped
with
reversible
front
panels in order to accom-
modate
a variety
of colors. Custom wood panels may also be used. Consult
the
Use and Care Guide for instructions
on changing front panels.
FIG. 1
The lower front
panel must be removed to enable plumbing
and electrical
con-
nections
to be made. To remove lower panel, take out two screws (C) and lock
washer (D). With
index fingers,
push support
tabs (B) up, and pull bottom
of
lower panel outward
to clear tabs of kickboard.
Slide lower panel down until side
flanges
are clear of evaporation
channel
support
(A). Reverse procedure
when
replacing
lower panel.
PRELIMINARY
ROUGH-IN
0
1
CABINET
OPENING
SHADED AREA SHOULD
BE FREE
of ALL PLUMBIND
AND ELECTRICAL CONNMOM
For dishwasher
to be flush with adjacent cabinets, there must be a minimum
of 24-l/4"
under counter
cabinet
depth available
for installation.
To estab-
lish a reference
line for purposes of providing
plumbing
and electrical
con-
nections
to the dishwasher,
measure 21"
from
the wall. (This is the front
edge of dishwasher
kick panel. There is a 3" toe space from the front of the
kick panel to the front
edge of the dishwasher
with
a standard
metal front
panel.) Cabinets 23-l/2"
to 23-5/8"
deep from wall to front of cabinet may
be accommodated
by removing
dry or plaster wall, baseboard and quarter
round directly
behind the dishwasher.
NOTE:
For corner
installation,
allow
2" clearance
for adjacent
cabinet.
CAUTION:
Make sure dishwasher
is not installed
under a surface burner or
warming
plate where the heat would
damage the water supply tubing.
If the
rear cross channel interferes
with the plumbing
and/or electrical
connections,
it may be relocated
as shown in Fig. 3 to create more clearance between the
cross channel and the floor.
-2-
FIG. 2