KitchenAid KEBC177KBL05 Istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno KitchenAid KEBC177KBL05. KitchenAid KEBC177KBL05 5. 27" electric built-in single and double ovens
Stampa la pagina
if codes permit and a separate grounding
wire is used, it is recommended
that a
qualified electrician determine that the
grounding path and wire gauge is in
accordance with local codes,
Do Not ground to a gas pipe.
Check with a qualified electrician if you are
not sure oven is properly grounded.
Do Not have a fuse in the neutral or
grounding circuit,
This oven must be connected to a
grounded metat, permanent wiring system,
Oven must be connected to the proper
eUectdcaU vokage and frequency as specified
on the modeU/sedaUrating pUate.(The
modeU/sedaUrating pUateis Uocated on the
oven door or on the oven frame.)
[_ Models rated from 7.3 to 9.6 kW at 240
volts (5.5 to 7.2 kW at 208 volts) require a
separate 4g-ampere circuit. Models rated
at 7.2 kW and below at 240 volts (5.4 kW
and below at 208 volts) require a
separate 3g-ampere circuit.
[_ A time-delay
fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect
(or circuit breaker box} through flexible,
armored or non-metallic sheathed, copper
cable (with grounding wire}.
[_ Flexible armored cable from appliance
should be connected directlyto junction
box.
[_ Fuse both sides ofthe line.
[_ A U.L.-listed conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections
must conform
with the rating of the appliance and to the
requirements
of the National Electrical
Code, ANSI/NFPA 70 -- latest edition% or
Canadian Electrical Code, C22.1-1982 and
C22.2 No. 01982 (or latest edition) ee and all
local codes and ordinances.
if the house has aluminum wiring, follow the
procedure bebw.
a.) Connect the aluminum wiring to the
copper wire using special connectors
designed and Underwriters Laboratories°
listed for joining copper to aluminum.
Follow the electrical connector
manufacturer's recommended procedure.
b.) Aluminum/copper
connection must
conform with local codes and industry-
accepted wiring practice.
Copies
of the standards
listed
may be obtained
from:
National
Fire Protection
Association
Batterymamh
Park
Quincy,
Massachusetts
02269
e_ CSA International
8501 East Pleasant
Valley
Road
Cleveland,
Ohio
44131=5575
Check oven
operation,
_
Grasp oven
frame to rift
oven,
i
11
_
power
supply
came
I
_
Remove
shipping
feet,
Preparation
Excessive
Weight Hazard
Use two or more people to move and
instatl oven.
Failure to folmow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, check that oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front rower
corners
of oven.
Do Not remove
shipping
feet.
Remove
oven
door.
Use screws to attach
oven to cabinet,
Reattaah
side
trim.
Remove
trim screws.
Remove
side
trim.
_
Use screws to
attach oven to
cabinet,
power
au
Remove
shipping
feet.
Cheek oven
_]
operation,
{eattaah side
trim,
Remove
side
trim,
Remove trim
screws.
Remove
oven doors.
Replace
oven
door
latch
on the
hinge
in rocked
position
=
door
free
to open
and
close
latch
on the
hinge
in unlocked
position
= door
ready
for removal
Remove trim screw.
Pull trim out,
Pull top oftdm
down,
[] Turn power supply off. Move oven
, Remove and discard shipping materials,
tape and protective film from the oven.
Do Not remove shipping base or
shipping feet at the front lower corners
of oven. The shipping feet will protect
the lower oven trim untit oven is
inserted into cabinet.
, Remove and set aside racks and other
parts from inside oven.
[] Completely open oven door. in both
back corners of the door you wiil see door
latches in the locked position. Rotate both
latches forward to the unlocked position.
Grasp outside edges of door with both hands.
Begin closing door, at the moment the door
stops closing, lift and puii door toward you.
Set door aside on a protective surface.
[] Remove trim screws attaching right
and left side trim to oven. Grasp the bottom
end of trim and pull away from oven. Slide
top end of trim downward to remove trim
from oven. Take care not to scratch other
surfaces with ends of trim. Set trim and
screws aside on protected surface.
Page 2