KitchenAid KEBC177KBL05 Istruzioni per l'installazione - Pagina 4
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Forno KitchenAid KEBC177KBL05. KitchenAid KEBC177KBL05 5. 27" electric built-in single and double ovens
Stampa la pagina
Electricalconnection
If your house has aluminum wiring, see
"Ebctdcal requirements", Page 2.
Electrical Shock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Electrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
This oven is manufactured
with white
{neutral}
power supply wire and a cabinet=connected
bare
grounding
wire twisted
together.
Feed oven cane through opening in
the cabinet. Make electrical connection
foUUowing the steps needed for your instaUUation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cabb to junction box through the
U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
ff local codes PERMIT
connecting
cabinet°
grounding
conductor
to
neutram white
wire
in
junction
box:
7. Connect the factory-crimped
bare and white oven cable wires
to the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cable from power supply
junction
red
__
w.ite
. .=
uit
Figure 2
cable from
connector
oven
If local codes DO NOT
cabinet-grounding
conductor
to neutral
white
wire
in
junction
box:
7. Separate the factory-
crimped bare and white
oven cable wires.
8. Connect white oven
cable wire to neutral
(white) wire in junction
box. See Figure 2.
9. Connect the bare
grounding oven cable
wire to a grounded wire
in the junction box. See
Figure 2.
10. Replace junction box
cover.
If connecting to a
four-wire electrical
system:
7. Separate bare and white
oven cable wires.
8. Connect white oven cable
wire to neutral (white} wire
in junction box. See
Figure 2.
9. Connect the bare
grounding oven cable wire
to the green grounding
wire in junction box. Do
Not connect bare
grounding wire to neutral
{white} wire in junction
box. See Figure 2.
10. Replace junction box
cover.
Attachment
Carefully push against seaJ area of oven
front frame when pushing oven into
cabinet.
Do Not push against outside edges.
5[]
Lift oven into
cabinet
cutout using the
oven.opening as an area
I I"r___>_
to gnp
I
\
C
4 screws
u Replace oven racks.
9_
Reinstall the oven door by inserting ends of
hinges into hinge slots in the oven frame. Push
hinges in as far as they wiil go. Open the door (you
wiil feel the door drop into place) and rotate both
hinge latches back to the locked position.
Close and open the door to check that the door
closes and opens completel% If door does not
dose or open completely, repeat the door removal
step and reinstall door as described above.
Repeat for lower oven door.
shipping
foot
Push against seal area of front frame to
push oven into cabinet until shipping feet
almost contact cabinet. Use a Phillips
screwdriver to remove screws attaching
shipping feet. Remove and discard shipping
feet.
Push oven completely into cabinet and
center oven in cabinet cutout.
m important: Securely fasten oven to
cabinet using the screws provided (two
screws for a single oven or four screws for a
double oven). Insert the screws through hobs
in mounting rails. Do Not overtighten screws.
Slide top
of trim up,
Push trim
into place.
Replace
2!#
trim screw.
/
7m
Slide top end of each trim upward onto
oven side rails. Push each trim into place at
bottom of trim. Use screws to attach each trim
to oven. Take care not to scratch other
surfaces with ends of trim.
Check operation
Turn on power supply. The
display panel will light up briefly. "PF"
should appear in the temperature display.
ir
', ....
,/
',
!
i_i
iJ
BAKE ]iBRO&
CLEAN!
i!
I,
i_,
I
/
....
i ',
,i
m
Check the operation of your single oven.
Press the "BROIL" pad. "BROIL" will appear
in the display. Press the "START" pad.
Page 3
Make sure the oven door is closed and the
"ON" light is shown in the display area. After
2 minutes, partially open oven door. You
should feel heat from the oven. Press the
"CANCEL" pad.
Check the operation of your double oven.
Press the "Upper Oven" pad. Press the
"BROIL" pad. "BROIL" will appear in the
displa% Press the "START" pad. Make sure
the oven door is closed and the "ON" light is
shown in the display area. After 2 minutes,
partially open oven door. You should feel heat
from the oven. Press the "CANCEL" pad.
Press the "Lower Oven" pad and repeat the
steps you completed for checking the upper
oven.
tf your oven does not heat or an "F", followed
by
a number,
appears inthe display, contact your
dealer or check the
"If you need service..."
section of this Installation
Instructions.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep
installation
Instructions
and Guide cmoseto oven
for easy reference.