Aqua Cooler AC-PV8EBFY-ASM Manuale d'uso e manutenzione - Pagina 7

Sfoglia online o scarica il pdf Manuale d'uso e manutenzione per Fontana da esterno Aqua Cooler AC-PV8EBFY-ASM. Aqua Cooler AC-PV8EBFY-ASM 11.

Stampa la pagina

SET-UP GUIDES CONT.

BOTTLE FILLER ELECTRONICS:

Please review the installation section first. Before installing upper panel assembly with electronic

bottle filler: change units from gallons (default setting) to litres. To ease access to the remote

toggle button for programming once the panel assembly and fountain is installed, feed the

remote toggle button through the fountain mounting plate.

Factory default program settings:

• Units: Gallons

• Unfiltered unit

• Flow meter = Rate selected

• Filter capacity = 1250 gallons (4731L) for VersaFilter

• Bottle count = 0.5L (1 bottle)

• Flow rate = 1.2 GPM

• 20s max dispense time.

To change the program settings, follow these steps:

DISPLAY

ACTION

000000000 BOTTLES

Depress button for 3 seconds to enter into the following menu settings and make changes.

REUSED

Note: at anytime it will exit menu and save settings when idle for 10 seconds (no button press) and

(Home Screen)

revert back to Home Screen.

LTR/GAL

Depress button for 3 seconds to change from Gallons to Litres, or momentary press to advance to

GAL

next menu.

UNFILT/FILT?

Depress button for 3 seconds to change from Unfiltered to Filtered unit, or momentary press to

UNFILT UNIT

advance to next menu

FLOW METER?

Depress button for 3 seconds to change from Rate Selected to (Flow) Meter Enabled, or

RATE SELECTED

momentary press to advance to next menu

SELECT RATE

To change flow rate, momentarily depress button to change whole gallon digit.

1.2 GPM UNIT

Hold button 3 seconds to advance to TENTHS of gallon digit.

Depress momentarily to change the digit.

Hold button 3 seconds to advance to the next menu.

RESET 000000000

Depress button for 3 seconds to reset Gallon or Litre count, or momentary press to advance to

GALLON CNT

next menu

[LTR COUNT]

FILT CAPAC

Depress button for 3 seconds to change filter capacity to 3000 GAL [11355 Litres] for Versafiller I

OF 1250 GAL

or Galaxi green filter, or momentary press to advance to next menu

[4731 LTR]

3 sec rule?

Depress button for 3 seconds to switch from 0.5L bottle to 3 sec rule, or momentary press to

0.5L

advance to next menu. (The 3 Sec rule increases the bottle count based on a 3 second dispense.)

RESET 00000000

Depress button for 3 seconds to reset (Home Screen) BOTTLES REUSED count, or momentary

BOT COUNT?

press to advance to next menu.

Bot Filler

Depress button for 3 seconds to change maximum dispense time to 10, 20, or 30 seconds, or

Set_time:20s

momentary press advance to next menu.

RUN CAL

Depress button for 3 seconds to run calibration again, or momentary press to advance to next

AGAIN?

menu.

REMOVING FROM SERVICE

• Disconnect the power supply.

• Disconnect the water supply.

• Drain cooler by removing grille, closing supply valve, and draining water.

• Remove the drain plug and bubbler.

Your Partner in Cool.

MAINTENANCE

The only maintenance required is the removal of dirt and lint from the condenser. Inspection

should be made at 3 mount intervals. Remove the grille and clean the condenser with a vacuum

attachment.

This unit is equipped with a hermetically sealed compressor. No additional lubrication is

required. The fan motor installed on this unit seldom needs oiling. If required, a few drops of

SAE 10 oil should be used.

Aqua Cooler recommends the unit to be checked every month, ensuring there is no blockage in

the condenser or in the back of the unit. Please remove all potentially harmful factors to prevent

any scratch or damage to the unit.

If customers require the unit's spare parts information, please contact the Aqua Cooler service

department for further assistance. The direct line is located on the back of this manual.

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

Controller is faulty

Temperature sensor is faulty

Controller display is faulty

No water flowing out of

Water source has been suspended

the unit

The system is clogged

Solenoid valve is faulty

Unit does not dispense cold

The cooling controller is turned off

water

Power failure

The ventilation around the unit is

insufficient

System malfunction

The temperature of the incoming water

it too high

Unit is noisy during operation

Chiller unit in the machine is not level

Chiller unit is touching other objects

The water being dispensed

This is not uncommon with new

has a strange taste.

water oolers. Do not worry, this is not

dangerous to your health.

MARKS

The appliance complies with applicable ACMA regulatory arrangements (Regulatory Compliance

Mark) and WaterMark WMTS 105:2016.

REMEDY

Check sensor connections.

Contact Aqua Cooler service team.

Restore water supply

Check the pipes

Check controller and cable connections

Check the position of the mechanical thermostat

and set to desired temperature

Check the power cord is properly plugged in or if

there is a power outage

Ensure sufficient ventilation space around the unit

Contact Aqua Cooler service team.

Ensure the unit is not placed in direct sunlight or

close to other heat sources

Place the chiller unit on a level flat surface.

Ensure the chiller is standing free of any surrounding

objects.

Flush as per installation instructions. Perform

cleaning procedure.