Aqua Quip QC Series Istruzioni per l'installazione e manuale d'uso
Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso per Illuminazione della piscina Aqua Quip QC Series. Aqua Quip QC Series 4. Surface-mounted led retro-fit pool light
Anche per Aqua Quip QC Series: Istruzioni per l'installazione e manuale d'uso (4 pagine)
Stampa la pagina
INSTALLATION INSTRUCTIONS & OWNERS MANUAL
INSTALLER
POOL OWNER
THESE INSTALLATION INSTRUCTIONS APPLY TO
AQUA-QUIP QC SURFACE MOUNTED LED RETRO-FIT LIGHTS ONLY.
All QC Series LED Lights operate from a VARIABLE SUPPLY VOLTAGE
QC Series Surface Mounted LED Retro-Fit Pool Lights are designed for use
in concrete swimming pools, please read entire manual before proceeding
Step 1: Universal Mounting Bracket (UniBracket) Installation Instructions
A) Ensure existing pool light is switched off.
B) Remove existing pool light from pool wall by following the instructions in the chart below.
C) Cut the existing pool light cable as close as possible to the pool light. At this stage, if there is insufficient cable
length to conveniently attach the QC Quick Connect Plug Kit, then an extension cable will be required. See part
number 7 on page 4.
D) Align holes in UniBracket with the corresponding holes in the existing mounting plate and affix using screws
saved in Step B. The word "TOP" is moulded into the UniBracket, be sure to affix it the correct way.
The UniBracket has a series of numbered screw holes marked on it, use the chart below to determine which
screw holes to use.
Existing Light
Stroud C150
Remove pool light using one screw at top. Unscrew Mounting Skirt from the Wall Ring and keep the 4
screws. Use the 4 screws to mount the UniBracket on top of the Wall Ring using the screw hole provi-
sions marked #2.
Waterco Litestream
Remove pool light using one screw at top. Unscrew the rectangular Wall Bracket from the Wall Ring
and keep the 4 screws to mount the UniBracket on top of Wall Ring, using screw hole provisions
marked #3.
Swimworld
Remove pool light using 2 screws on left & right, keep the screws. If the Wall Bracket is plastic: Cut the
2 plastic mounting posts flush with the pool wall. Use the 2 screws to mount the UniBracket to the pool
wall, using the 2 screw hole provisons marked #5. If the Wall Bracket is stainless steel, then pool water
level should be lowered and steel lugs cut off. UniBracket should then be mounted to pool wall using
APL071 Retro-Fit Screw Kit (not supplied), using screw hole provisions marked #2.
Spa Electrics SE3M
Remove pool light using one screw at top. Unscrew the rectangular Hook Bracket from pool wall. Use
the 2 screws to mount the UniBracket onto pool wall using the screw hole provisions marked #7.
Poolrite
Remove pool light using one screw at top. Unscrew the Mounting Plate from Wall Levelling Ring and
keep the 3 screws. Use the 3 screws to fit the UniBracket to the Wall Levelling Ring using screw hole
provisions marked #8.
Stroud SM400/Filtrite
Remove pool light. Fit the APL075 Locating Bar (not supplied) horizontally behind the "lip" in the pool
wall. Align the 2 holes marked #4 on UniBracket with the bolts on the Locating Bar and use the stain-
less steel wing nuts (included in APL075) to secure UniBracket to wall. It may be necessary to trim the
ends of the locating bar by a few millimetres if the fit is too tight. APL075 Locating Bar Assembly is an
optional extra and can be ordered at place of purchase.
Autumn Solar/Questa
Remove pool light using one screw at top. Unscrew the rectangular Hook Bracket from pool wall. Use
Chameleon/Magic
the 2 screws to fit the UniBracket onto pool wall using the screw provisions marked #6.
Aqua-Quip
No need to fit the new UniBracket, unless original bracket is damaged.
E) Proceed to Step 2 once the Unibracket is mounted.
Please Note: The Aqua-Quip QC Series Surface Mounted LED Retro-Fit Pool Light can also be used to replace
the following brands of Niche/Recessed pool lights: Spa Electrics, Waterco Britestream, AstralPool Hurlcon,
Lumascape, Aqua-Star, Purex and Swimcraft, contact Aqua-Quip for more details.
QC SERIES SURFACE MOUNTED LED RETRO-FIT POOL LIGHTS – INSTALLATION INSTRUCTIONS & OWNERS MANUAL
QC SERIES
– READ ENTIRE INSTRUCTION SHEET BEFORE
PROCEEDING TO INSTALL.
– PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
PLEASE NOTE
from 12volt AC through to 32volt AC.
with the installation.
Instructions to remove existing light and fit the UniBracket
SURFACE MOUNTED LED
RETRO-FIT POOL LIGHT
1