Aqua Quip QC Series Installation Instructions & Owner's Manual

Browse online or download pdf Installation Instructions & Owner's Manual for Swimming Pool Lighting Aqua Quip QC Series. Aqua Quip QC Series 4 pages. Surface-mounted led retro-fit pool light
Also for Aqua Quip QC Series: Installation Instructions & Owner's Manual (4 pages)

Print Page

INSTALLATION INSTRUCTIONS & OWNERS MANUAL

INSTALLER

POOL OWNER

THESE INSTALLATION INSTRUCTIONS APPLY TO

AQUA-QUIP QC SURFACE MOUNTED LED RETRO-FIT LIGHTS ONLY.

All QC Series LED Lights operate from a VARIABLE SUPPLY VOLTAGE

QC Series Surface Mounted LED Retro-Fit Pool Lights are designed for use

in concrete swimming pools, please read entire manual before proceeding

Step 1: Universal Mounting Bracket (UniBracket) Installation Instructions

A) Ensure existing pool light is switched off.

B) Remove existing pool light from pool wall by following the instructions in the chart below.

C) Cut the existing pool light cable as close as possible to the pool light. At this stage, if there is insufﬁcient cable

length to conveniently attach the QC Quick Connect Plug Kit, then an extension cable will be required. See part

number 7 on page 4.

D) Align holes in UniBracket with the corresponding holes in the existing mounting plate and afﬁx using screws

saved in Step B. The word "TOP" is moulded into the UniBracket, be sure to afﬁx it the correct way.

The UniBracket has a series of numbered screw holes marked on it, use the chart below to determine which

screw holes to use.

Existing Light

Stroud C150

Remove pool light using one screw at top. Unscrew Mounting Skirt from the Wall Ring and keep the 4

screws. Use the 4 screws to mount the UniBracket on top of the Wall Ring using the screw hole provi-

sions marked #2.

Waterco Litestream

Remove pool light using one screw at top. Unscrew the rectangular Wall Bracket from the Wall Ring

and keep the 4 screws to mount the UniBracket on top of Wall Ring, using screw hole provisions

marked #3.

Swimworld

Remove pool light using 2 screws on left & right, keep the screws. If the Wall Bracket is plastic: Cut the

2 plastic mounting posts ﬂush with the pool wall. Use the 2 screws to mount the UniBracket to the pool

wall, using the 2 screw hole provisons marked #5. If the Wall Bracket is stainless steel, then pool water

level should be lowered and steel lugs cut off. UniBracket should then be mounted to pool wall using

APL071 Retro-Fit Screw Kit (not supplied), using screw hole provisions marked #2.

Spa Electrics SE3M

Remove pool light using one screw at top. Unscrew the rectangular Hook Bracket from pool wall. Use

the 2 screws to mount the UniBracket onto pool wall using the screw hole provisions marked #7.

Poolrite

Remove pool light using one screw at top. Unscrew the Mounting Plate from Wall Levelling Ring and

keep the 3 screws. Use the 3 screws to ﬁt the UniBracket to the Wall Levelling Ring using screw hole

provisions marked #8.

Stroud SM400/Filtrite

Remove pool light. Fit the APL075 Locating Bar (not supplied) horizontally behind the "lip" in the pool

wall. Align the 2 holes marked #4 on UniBracket with the bolts on the Locating Bar and use the stain-

less steel wing nuts (included in APL075) to secure UniBracket to wall. It may be necessary to trim the

ends of the locating bar by a few millimetres if the ﬁt is too tight. APL075 Locating Bar Assembly is an

optional extra and can be ordered at place of purchase.

Autumn Solar/Questa

Remove pool light using one screw at top. Unscrew the rectangular Hook Bracket from pool wall. Use

Chameleon/Magic

the 2 screws to ﬁt the UniBracket onto pool wall using the screw provisions marked #6.

Aqua-Quip

No need to ﬁt the new UniBracket, unless original bracket is damaged.

E) Proceed to Step 2 once the Unibracket is mounted.

Please Note: The Aqua-Quip QC Series Surface Mounted LED Retro-Fit Pool Light can also be used to replace

the following brands of Niche/Recessed pool lights: Spa Electrics, Waterco Britestream, AstralPool Hurlcon,

Lumascape, Aqua-Star, Purex and Swimcraft, contact Aqua-Quip for more details.

QC SERIES SURFACE MOUNTED LED RETRO-FIT POOL LIGHTS – INSTALLATION INSTRUCTIONS & OWNERS MANUAL

QC SERIES

– READ ENTIRE INSTRUCTION SHEET BEFORE

PROCEEDING TO INSTALL.

– PLEASE KEEP THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

PLEASE NOTE

from 12volt AC through to 32volt AC.

with the installation.

Instructions to remove existing light and ﬁt the UniBracket

SURFACE MOUNTED LED

RETRO-FIT POOL LIGHT