Dell 3WY51 Istruzioni per l'aggiornamento del firmware - Pagina 6
Sfoglia online o scarica il pdf Istruzioni per l'aggiornamento del firmware per Interruttore Dell 3WY51. Dell 3WY51 17. Emcnetworking switches
Stampa la pagina
- 1. Table of Contents
- 2. Introduction
- 3. Global Support
- 4. Firmware Upgrade Overview
- 5. Firmware Downgrade Overview
- 6. How to Access Serial Console on Dell EMC Networking N1500 Series Switches
- 7. Upgrade Example of Dell EMC Networking N1500 Series Switches
- 8. Upgrade Stack of Dell EMC Networking N1500 Series Switches
- 9. Switch Recovery Procedure
- 10. Switch Recovery Example
- 11. End of Document
Upgrade Dell EMC Networking N1500 Series Switches
2. Set an enable password and save the configuration (not required if an alternative enable authentication
method is already configured).
console#configure
console(config)# enable password <password>
console(config)# exit
console# copy running-config startup-config
3. Download the 6.5.2.9 firmware image from a TFTP server.
console#copy tftp://10.10.10.200/N1500v6.5.2.9.stk backup
Transfer Mode.................................. TFTP
Server IP Address.............................. 10.10.10.200
Source File Path............................... ./
Source Filename................................ N1500v6.5.2.9.stk
Data Type...................................... Code
Destination Filename........................... backup
Management access will be blocked for the duration of the transfer
Are you sure you want to start? (y/n) y
TFTP Code transfer starting...
27888574 bytes transferred...
File contents are valid. Copying file to flash...
Attempting to send the STK file to other units in the stack...
File transfer operation completed successfully.
console#show version
Machine Description............... Dell Networking Switch
System Model ID................... N1548P
Machine Type...................... Dell Networking N1548P
Serial Number..................... 15114M0002LF
Manufacturer...................... 0xbc00
Burned In MAC Address............. 001E.C9E5.BD0F
System Object ID.................. 1.3.6.1.4.1.674.10895.3066
SOC Version....................... BCM56150_A0
HW Version........................ 1
CPLD Version...................... 16
unit
active
----- ------------ ------------ ----------------- -----------------
1
6.3.3.14
NOTE:
Set the image to use as the boot (active) image after the switch resets.
Images on the N1500 series switches are named active and backup.
4. Activate the
6.5.2.9
console#boot system backup
Activating image backup ..
5. HiveAgent application has been upgraded to a newer version 1.1.16.0 in 6.5.2.9 release for N1500, N2000
and N3000 switches. To ensure that new HiveAgent application is properly installed in the switch, below
commands must be run before upgrading to 6.5.2.9 from a 6.3.x.x release. This step is not applicable for
customers managing their switches via HiveManager.
console#application stop hiveagent
console#delete user-apps/ah_ha.conf_s
Delete user-apps/ah_ha.conf_s ? (y/n) y
console#delete user-apps/hiveagent_pr_s
Delete user-apps/hiveagent_pr_s ? (y/n) y
console#delete user-apps/ah_ha.conf
Delete user-apps/ah_ha.conf ? (y/n) y
console#delete user-apps/hiveagent_pr
Delete user-apps/hiveagent_pr ? (y/n) y
console#delete user-apps/hiveagent
Delete user-apps/hiveagent ? (y/n) y
backup
current-active
6.5.2.9
6.3.3.14
firmware
Page 4
next-active
6.3.3.14