AquaPurr eC Manuale - Pagina 3

Sfoglia online o scarica il pdf Manuale per Prodotto per la cura degli animali domestici AquaPurr eC. AquaPurr eC 4.
Anche per AquaPurr eC: Manuale d'uso (12 pagine)

Stampa la pagina

Installing your AquaPurr

Attach the diverter valve to your faucet

Remove the aerator from your faucet. Then

determine if your faucet has outside or inside

threads:

Outside threads

If your faucet has outside threads,

screw the diverter valve onto the

faucet by turning the swivel collar.

If the diverter valve threads are

too large then you might need a

13/16" adapter. Contact us and

we will send you one.

Inside threads

If your faucet has inside threads,

select the thread adapter that fits

your faucet.

Insert the rubber washer that

matches the thread adapter and

screw the thread adapter into the

faucet.

Screw the diverter valve onto the

thread adapter by turning the

swivel collar.

If you are having difficulty getting the diverter valve tight, rotate

the diverter valve backward and forward while turning the swivel

collar.

If none of the provided thread adapters fit, we can help!

Text us or give us a call toll free at 833-278-2787 or email

us at [email protected]. We will figure

out the adapter you need and send it to you. Refer to

enclosed chart to determine your aerator size.

Install Spigot:

Install the rigid plastic

drinking spigot in the base

unit.

Simply push the end of the

spigot into the top of the fitting on the base unit. Confirm the

installation is secured by slightly pulling the spigot—it should not

pull out.

You may need to push a bit harder than you think to secure the

spigot. If you see some water leak from that joint when you turn

on faucet, you will know it is not fully inserted.

To remove the spigot, simply push down and hold the collar on

the fitting while pulling out the spigot.

Install flexible tube

Install the flexible tube in the base unit.

Simply push the end of the tube into the

fitting on the side of the base unit.

Confirm the installation is secured by

slightly pulling the tube —it should not

pull out.

You may need to push a bit harder than you think to secure the

tube. If you see some water leak from that joint when you turn

on faucet, you will know it is not fully inserted.

To remove the tube, simply push down and hold the collar on

the fitting while pulling out the tube. Note: if you want to

remove the tube after the AquaPurr has been in use, be sure to

unplug the AquaPurr and turn off your faucet before removing

tube from base unit.

Position the AquaPurr eC next to your sink

The AquaPurr eC can be placed on either side of your sink. Once

you decide which side of the sink to place the AquaPurr eC, just

lift the lid of the base unit and rotate it as needed so that the

drinking spigot is positioned over your sink, then place lid back

onto base unit.

Attach power cord

Insert the power cord into the AquaPurr

eC as shown and plug the power cord into

the wall power outlet.

Secure the AquaPurr to countertop

Peel the backing off the 3M Command strips attached to the

bottom of the AquaPurr eC.

Set the AquaPurr eC in desired position next to your sink and

press down on the top edges of the AquaPurr eC base unit to

secure the Command strips to your counter.

The 3M Command strips act like Velcro to secure the AquaPurr

eC to the counter top. The 3M Command strips allow you to

remove and reposition the AquaPurr eC.

Use of the 3M Command strips is required to help prevent

moving the AquaPurr eC away from the sink, which could cause

flowing water to land outside the sink, potentially causing water

damage.

Check for leaks

With the diverter valve set to AquaPurr mode, horizontal, and

the faucet turned on, make sure there are no leaks anywhere.

Look at the base of the faucet and even under the sink. Using

the diverter valve can sometimes stress older faucets and cause

them to leak.

You're ready to use your AquaPurr eC!