AquaPurr eC Manuel - Sayfa 3
Evcil Hayvan Bakım Ürünü AquaPurr eC için çevrimiçi göz atın veya pdf Manuel indirin. AquaPurr eC 4 sayfaları.
Ayrıca AquaPurr eC için: Kullanıcı Kılavuzu (12 sayfalar)
Sayfayı YazdırInstalling your AquaPurr
Attach the diverter valve to your faucet
Remove the aerator from your faucet. Then
determine if your faucet has outside or inside
threads:
Outside threads
If your faucet has outside threads,
screw the diverter valve onto the
faucet by turning the swivel collar.
If the diverter valve threads are
too large then you might need a
13/16" adapter. Contact us and
we will send you one.
Inside threads
If your faucet has inside threads,
select the thread adapter that fits
your faucet.
Insert the rubber washer that
matches the thread adapter and
screw the thread adapter into the
faucet.
Screw the diverter valve onto the
thread adapter by turning the
swivel collar.
If you are having difficulty getting the diverter valve tight, rotate
the diverter valve backward and forward while turning the swivel
collar.
If none of the provided thread adapters fit, we can help!
Text us or give us a call toll free at 833-278-2787 or email
us at [email protected]. We will figure
out the adapter you need and send it to you. Refer to
enclosed chart to determine your aerator size.
Install Spigot:
Install the rigid plastic
drinking spigot in the base
unit.
Simply push the end of the
spigot into the top of the fitting on the base unit. Confirm the
installation is secured by slightly pulling the spigot—it should not
pull out.
You may need to push a bit harder than you think to secure the
spigot. If you see some water leak from that joint when you turn
on faucet, you will know it is not fully inserted.
To remove the spigot, simply push down and hold the collar on
the fitting while pulling out the spigot.
Install flexible tube
Install the flexible tube in the base unit.
Simply push the end of the tube into the
fitting on the side of the base unit.
Confirm the installation is secured by
slightly pulling the tube —it should not
pull out.
You may need to push a bit harder than you think to secure the
tube. If you see some water leak from that joint when you turn
on faucet, you will know it is not fully inserted.
To remove the tube, simply push down and hold the collar on
the fitting while pulling out the tube. Note: if you want to
remove the tube after the AquaPurr has been in use, be sure to
unplug the AquaPurr and turn off your faucet before removing
tube from base unit.
Position the AquaPurr eC next to your sink
The AquaPurr eC can be placed on either side of your sink. Once
you decide which side of the sink to place the AquaPurr eC, just
lift the lid of the base unit and rotate it as needed so that the
drinking spigot is positioned over your sink, then place lid back
onto base unit.
Attach power cord
Insert the power cord into the AquaPurr
eC as shown and plug the power cord into
the wall power outlet.
Secure the AquaPurr to countertop
Peel the backing off the 3M Command strips attached to the
bottom of the AquaPurr eC.
Set the AquaPurr eC in desired position next to your sink and
press down on the top edges of the AquaPurr eC base unit to
secure the Command strips to your counter.
The 3M Command strips act like Velcro to secure the AquaPurr
eC to the counter top. The 3M Command strips allow you to
remove and reposition the AquaPurr eC.
Use of the 3M Command strips is required to help prevent
moving the AquaPurr eC away from the sink, which could cause
flowing water to land outside the sink, potentially causing water
damage.
Check for leaks
With the diverter valve set to AquaPurr mode, horizontal, and
the faucet turned on, make sure there are no leaks anywhere.
Look at the base of the faucet and even under the sink. Using
the diverter valve can sometimes stress older faucets and cause
them to leak.
You're ready to use your AquaPurr eC!