HP 316095-B21 - StorageWorks Edge Switch 2/24 Nota di rilascio - Pagina 7

Sfoglia online o scarica il pdf Nota di rilascio per Interruttore HP 316095-B21 - StorageWorks Edge Switch 2/24. HP 316095-B21 - StorageWorks Edge Switch 2/24 25. Edge switch release notes
Anche per HP 316095-B21 - StorageWorks Edge Switch 2/24: Manuale di aggiornamento (9 pagine), Manuale (41 pagine), Manuale (40 pagine), Nota di rilascio (32 pagine), Nota di rilascio (27 pagine), Manuale (26 pagine), Nota di rilascio (27 pagine), Manuale di istruzioni per l'installazione (24 pagine), Nota di rilascio (23 pagine), Nota di rilascio (23 pagine), Nota di rilascio (22 pagine), Nota di rilascio (23 pagine), Nota di rilascio (19 pagine), Nota di rilascio (19 pagine), Nota di rilascio (18 pagine), Manuale di istruzioni (17 pagine), Nota di rilascio (17 pagine), Istruzioni per l'aggiornamento (16 pagine), Manuale di istruzioni (16 pagine), Manuale di istruzioni per l'installazione (16 pagine), Nota di rilascio (16 pagine), Nota di rilascio (17 pagine), Nota di rilascio (17 pagine), Nota di rilascio (11 pagine)

To disable the SNMP Proxy:

Open a Telnet session.

Enter admin start and press ENTER.

Enter set setup snmp and press ENTER.

Set the ProxyEnabled setting to False.

The message Do you want to save and activate the

snmp setup?

Enter y and press ENTER.

Installing McDATA 4Gb SAN Switch ﬁrmware

To ensure that the McDATA 4Gb SAN Switch ﬁrmware install results in a Non Disruptive

Code Load and Activation (NDCLA), and does not require a hard reset, close all

instances of the McDATA Web Server embedded GUI except for the instance performing

the install. If more than one instance is open when the install completes, a hard reset is

required which disrupts all switch trafﬁc.

Managing McDATA 4Gb SAN Switch considerations

DO NOT use the Element Manager Fabric Binding feature on McDATA 4Gb SAN

Switches. Element Manager Fabric Binding does not synchronize with HAFM Fabric

Binding. If both Fabric Binding features are used, a disconnect can occur between the

Element Manager and HAFM.

Examples

•

If you activate an ISL set while a port set is already active, the ISL set takes over

and vice versa. This is working as designed.

•

If you activate Switch Binding using the Element Manager, and then activate

Fabric Binding using HAFM, the McDATA 4Gb SAN Switch copies and appends

the Fabric Binding to the current Switch Binding security policy. This is working

as designed. However, if you then deactivate Fabric Binding using HAFM, it

only deactivates on legacy M-Series and McDATA switches. You must deactivate

the policy using the Element Manager to deactivate it on the McDATA 4Gb

SAN Switch.

If you also had Switch Binding activated and the learned Fabric Binding policy

is merged, Switch Binding becomes deactivated. A security hole exists if you

do not realize this; however, it is apparent that this happens when you look at

the active policy. Activate the policy you created using the Element Manager

again to enable Switch Binding.

•

If there is no Switch Binding activated in the Element Manager and Fabric

Binding is activated using HAFM, Fabric Binding can be deactivated only by

using HAFM. This is working as designed.

[n] is displayed.

(y/n) :

HA-Fabric Manager release notes