HP 316095-B21 - StorageWorks Edge Switch 2/24 Nota di rilascio - Pagina 8

Sfoglia online o scarica il pdf Nota di rilascio per Interruttore HP 316095-B21 - StorageWorks Edge Switch 2/24. HP 316095-B21 - StorageWorks Edge Switch 2/24 25. Edge switch release notes
Anche per HP 316095-B21 - StorageWorks Edge Switch 2/24: Manuale di aggiornamento (9 pagine), Manuale (41 pagine), Manuale (40 pagine), Nota di rilascio (32 pagine), Nota di rilascio (27 pagine), Manuale (26 pagine), Nota di rilascio (27 pagine), Manuale di istruzioni per l'installazione (24 pagine), Nota di rilascio (23 pagine), Nota di rilascio (23 pagine), Nota di rilascio (22 pagine), Nota di rilascio (23 pagine), Nota di rilascio (19 pagine), Nota di rilascio (19 pagine), Nota di rilascio (18 pagine), Manuale di istruzioni (17 pagine), Nota di rilascio (17 pagine), Istruzioni per l'aggiornamento (16 pagine), Manuale di istruzioni (16 pagine), Manuale di istruzioni per l'installazione (16 pagine), Nota di rilascio (16 pagine), Nota di rilascio (17 pagine), Nota di rilascio (17 pagine), Nota di rilascio (11 pagine)

•

If Switch Binding is activated using the Element Manager with an F-Port logged

in to the McDATA 4Gb SAN Switch that is not in the Switch Binding membership

list (for example, an administrator command has not logged out the unwanted

port), Fabric Binding cannot be activated using HAFM.

Minor code enhancements and ﬁxes in M-Series ﬁrmware 08.01.00

The release of ﬁrmware 08.01.00 incorporates some minor code enhancements and

ﬁxes, and is not a mandatory upgrade, though HP recommends that all Directors and

Edge Switches be upgraded to this version of ﬁrmware.

McDATA 4Gb SAN Switch Element Manager support

Provides support for launching the McDATA 4Gb SAN Switch Element Manager through

HAFM. Firmware 5.2.2.15.00 is the minimum version of ﬁrmware required for HAFM

Element Manager support.

Advanced Fabric Diagnostics enhancements

The following enhancements have been made to Advanced Fabric Diagnostics features

(requires ﬁrmware 08.01.00 or later; not supported by McDATA 4Gb SAN Switch):

•

Port Fencing—Building on E_Port or ISL Fencing introduced in ﬁrmware

07.xx.xx, Port Fencing policies have been enhanced to include F_Ports to block

malfunctioning devices attached to M-Series Directors and Edge Switches. Users

can conﬁgure policies to detect ports that are violating security rules, as well as

link-level problems, such as a port that repeatedly exits the active-link state.

If a user-deﬁned threshold is reached, the port is automatically blocked, and

the user is notiﬁed. Users can unblock ports manually to allow the ISL or

node to recover when the source of the problem is identiﬁed. Malfunctions in

connected hardware or Denial of Service (DoS) attacks can cause devices to

attempt repeated log-ins, which in extreme cases can impact fabric operations

adversely. Port Fencing can detect many of these conditions and prevent adverse

consequences.

Port Fencing is disabled by default. However, when enabled, default threshold

values are established for the different types of policies if the user has not

conﬁgured them manually. In most cases, the default policies provide a

reasonable level of protection, but further reﬁnement may be necessary to

accommodate speciﬁc SAN behavior.

During planned maintenance or service operations, HP recommends disabling

appropriate policies to prevent fencing of ports from expected behavior.

New CLI commands support this enhancement.

•

Embedded Port Log—CLI Enhancements enable users to specify trigger points

that will start and stop events from being written to the Embedded Port Log.

These triggers consist of a data pattern and offset into the Fibre Channel frame.