Shimano SG-8C20 Manuale di servizio - Pagina 9

Sfoglia online o scarica il pdf Manuale di servizio per Apparecchiature industriali Shimano SG-8C20. Shimano SG-8C20 36. Inter-8 coaster hub
Anche per Shimano SG-8C20: Istruzioni per l'assistenza tecnica (4 pagine)

Stampa la pagina

Pass the inner cable through the

SIS-SP40 outer casing through the

end with the plastic cap.

Aluminium cap

Plastic cap

If cutting the outer casing, cut it near the

end with the plastic cap while the cap is

still attached. Then make the cut end

perfectly round and attach the plastic cap.

Plastic cap

Remove the plastic cap.

Make the cut end

perfectly round.

Attach the plastic cap.

■ Cassette joint side

After checking that the end of the

outer casing is sitting securely in

the cable adjustment bolt of the

Revo-shift lever, attach the inner

cable fixing bolt unit to the inner

cable.

Inner cable fixing bolt unit

Note: Do not use this inner cable fixing bolt

unit with the CJ-4S30 cassette joint.

Inner cable fixing

nut

Inner cable fixing

washer

Inner cable fixing

10 mm

bolt

(Black)

Pass the inner cable

through the hole.

101 mm

Pull the inner cable while attaching the inner

cable fixing bolt unit.

Tightening torque:

4 – 6 N·m {40 – 60 kgf·cm}

Bring the cable around to the

cassette joint pulley, hold so that

the inner cable fixing nut is facing

to the outside (toward the fork

end), and then slide the flats part

of the inner cable fixing washer

into the gap in the pulley.

Flats part of inner

cable fixing washer

Gap in pulley

Inner cable

fixing nut

Pulley

CJ-8S20

JAPAN

Turn the cable 60º counterclockwise

and attach it to the hook.

Hook

CJ-8S20

JAPAN

Turn the

cable 60º

Attach the inner cable to the pulley

as shown in the illustration, pass the

inner cable through the slit in the

cassette joint bracket, and then

insert the end of the outer casing

securely into the outer casing holder.

Inner cable

Pulley

Bracket

Outer casing holder

Insert into

8 -

0 2

the outer

A J

casing

holder

Slit

Pass through the slit

If first inserting the outer casing into the

outer casing holder is easier, then first insert

the outer casing into the outer casing hold-

er, and then insert a 2 mm Allen key or a

#14 spoke into the hole in the cassette joint

pulley, and then turn the pulley so that the

inner cable fixing bolt unit fits into the gap

in the pulley.

Insert the inner

Insert into the

cable fixing bolt

outer casing

unit.

holder.

CJ-8S20

JAPAN

Turn the

Hole in pulley

pulley

2 mm Allen key or #14 spoke

Note:

Check that the inner cable is correctly seated

inside the pulley guide.

CJ-8S20

JAPAN

Guide

Not OK

10.

Secure the cable to the frame with

the outer casing bands.

10 cm

15 cm

10 cm

Outer casing bands

Adjusting the cassette joint

Set the Revo-shift lever to

Check to be sure that the yellow setting

lines on the cassette joint bracket and

pulley are aligned at this time.

Yellow setting lines

➃ ➃

Set to

The yellow setting lines on the cassette joint

are located in two places. Use the one that

is easiest to see.

When bicycle is standing up

Should be straight

Cassette joint

bracket

When bicycle is upside down

Should be straight

Cassette joint

bracket

If the yellow setting lines are not aligned,

turn the cable adjustment bolt of the

Revoshift lever to align the setting lines.

After this, move the Revo-shift lever once

➃ ➃

➀ ➀