Cisco Profile Series Manuale - Pagina 7

Sfoglia online o scarica il pdf Manuale per Sistema di conferenze Cisco Profile Series. Cisco Profile Series 16. Jbod on the 12g sas modular raid controller
Anche per Cisco Profile Series: Manuale introduttivo (41 pagine), Manuale d'uso (44 pagine), Manuale d'uso (7 pagine), Manuale introduttivo (35 pagine), Manuale di riferimento rapido (2 pagine), Manuale di installazione (44 pagine), Manuale di configurazione (13 pagine), Scheda di installazione (2 pagine), Manuale di installazione (2 pagine), Manuale di avvio rapido (4 pagine), Manuale di avvio rapido (4 pagine), Manuale di installazione (16 pagine), Manuale introduttivo (32 pagine), Manuale introduttivo (42 pagine), Manuale introduttivo (46 pagine)

Get To Know Your Switch

• 60-Watt PoE Ports—Highlighted in yellow. The 60-Watt PoE ports double the PoE power to 60W. This

• SFP+ Port (if present)—The small form-factor pluggable plus (SFP+) are connection points for modules

• Some SFP interfaces are shared with one other RJ-45 port, called a combo port. When the SFP is active,

• OOB Port (if present)—The Out of Band (OOB) port is a CPU Ethernet port that can be used only as a

Front Panel LEDs

The following are the global LEDs found on the devices:

• System—(Green) The LED lights steady when the switch is powered on, and flashes when booting,

• System LED - Every 20 seconds, the System LED will flash according to unit ID of the member unit.

is not found on the 250 devices nor on the SF350-48P device.

so that the switch can link to other switches. These ports are also commonly referred to as mini 10GigaBit

Interface Converter ports. The term SFP+ is used in this guide.

• The SFP+ ports are compatible with the following Cisco SFP 1G optical modules MGBSX1,

MGBLH1, MGBT1, as well as other brands.

• The Cisco SFP+ 10G optical modules that are supported in the Cisco switches are: SFP-10G-SR,

SFP-10G-LR, SFP-10G-SR-S, and SFP-10G-LR-S.

• The Cisco SFP+ Copper Cable modules that are supported in the Cisco switches are:

SFP-H10GB-CU1M, SFP-H10GB-CU3M, and SFP-H10GB-CU5M.

• The SFP+ port is a combination port, shared with one other RJ-45 port. When the SFP+ is active,

the adjacent RJ-45 port is disabled.

• The LEDs of the corresponding RJ-45 port flash green to respond to the SFP interface traffic.

the adjacent RJ-45 port is disabled.

management interface. Bridging between the OOB port and the in-band Layer 2 interface is not supported.

This does not appear on 250 devices.

performing self-tests, or acquiring an IP address. If the LED flashes Amber, the switch has detected a

hardware failure, a firmware failure, and/or a configuration file error.

• Flash = LED going off and then on again.

• According to unit ID of the unit. This means

• Unit 1 (if not active unit) - system LED will flash 1 time

• Unit 2 (if not active unit) - system LED will flash 2 times

• Unit 3 - system LED will flash 3 times

• Unit 4 -system LED will flash 4 times;

• The duration of each flash (LED off time) will be as follows:

• LED off time (in each flash) ~ 0.5 seconds.

• "Interim" LED on (between 2 LED offs) ~ 0.5 seconds

Front Panel LEDs

Get To Know Your Switch