Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion Nota di installazione - Pagina 10

Sfoglia online o scarica il pdf Nota di installazione per Hardware di rete Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion. Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion 24. Distributed forwarding card 4 for ws-x68xx, ws-x69xx, and select ws-x67xx modules
Anche per Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module Expansion: Nota di installazione (14 pagine), Manuale di soluzione (17 pagine), Nota di installazione (46 pagine), White Paper (19 pagine), Descrizione (1 pagine), Bollettino dei prodotti (6 pagine), Avviso (4 pagine), Scheda tecnica (9 pagine), Scheda tecnica (18 pagine), White Paper (18 pagine), Manuale di configurazione (8 pagine), Nota di installazione (28 pagine), Manuale di risoluzione dei problemi (11 pagine), Nota di installazione (18 pagine), Manuale d'uso (17 pagine), Manuale (19 pagine), Nota di installazione (36 pagine)

Installing the CSM

•

Removing the Module

This section describes how to remove an existing module from a Catalyst 6500 series switch chassis slot.

During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly

Caution

touch the backplane with your hand or any metal tool, or you could shock yourself.

Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into

Warning

beams or view directly with optical instruments.

To remove a supervisor engine or module from the chassis, perform these steps:

Disconnect any network interface cables that are attached to the supervisor engine or module.

Step 1

Verify that the captive installation screws on all of the modules in the chassis are tight.

Step 2

This step assures that the space that is created by the removed module is maintained.

Note

Loosen the two captive installation screws on the supervisor engine or module.

Step 3

Depending on the orientation of the slots in the chassis (horizontal or vertical), perform one of the

Step 4

following set of substeps:

Horizontal slots

Vertical slots

Place the module on an antistatic mat or antistatic foam, or immediately reinstall it in another slot.

Step 5

Catalyst 6500 Series Switch Content Switching Module Installation Note

Slot 1 is reserved for the supervisor engine.

Slot 2 can be used for a redundant supervisor engine if the supervisor engine in slot 1 fails.

If a redundant supervisor engine is not required, slots 2 through 6 on the 6-slot chassis, slots 2

through 9 on the 9-slot chassis, and slots 2 through 13 on the 13-slot chassis are available for

switching modules, such as the CSM.

The empty slots require filler plates, which are blank switching-module carriers that maintain

consistent airflow through the switch chassis.

If the captive installation screws are loose, the electromagnetic interference (EMI) gaskets on

the installed modules will push the modules toward the open slot, reducing the opening size and

making it difficult to install the replacement module.

Place your thumbs on the left and right ejector levers, and simultaneously rotate the levers outward

to unseat the module from the backplane connector.

Grasp the front edge of the module, and slide the module part of the way out of the slot. Place your

other hand under the module to support the weight of the module. Do not touch the module circuitry.

Place your thumbs on the ejector levers that are located at the top and bottom of the module, and

simultaneously rotate the levers outward to unseat the module from the backplane connector.

Grasp the edges of the module, and slide the module straight out of the slot. Do not touch the module

circuitry.

78-15751-01