Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE Manuale di istruzioni per l'installazione - Pagina 2

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Luce per esterni Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE. Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE 8. Led wall pack

Stampa la pagina

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

• To reduce the risk of death, personal injury or property damage from fire, electric

shock, falling parts, cuts/abrasions, and other hazards please read all warnings

and instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this

equipment, follow these general precautions.

• Commercial installation, service and maintenance of luminaires should be

performed by a qualified licensed electrician.

• For Residential installation: If you are unsure about the installation or

maintenance of the luminaires, consult a qualified licensed electrician and check

your local electical code.

• Maintenance of the luminaires should be performed by person(s) familiar with

the luminaires' construction and operation and any hazards involved. Regular

fixture maintenance programs are recommended.

• This fixture is intended to be connected to a properly installed and grounded UL

listed junction box.

• It will occasionally be necessary to clean the outside of the refractor/lens.

Refractor/lens should be washed in a solution of warm water and any mild, non-

abrasive household detergent, rinsed with clean water and wiped dry. Should

optical assembly become dirty on the inside, wipe refractor/lens and clean in

above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been

properly packed so that no parts should have been damaged during transit.

Inspect to confirm. Any part damaged or broken during or after assembly should

be replaced.

• Recycle: For information on how to recycle LED electronic products, please

visit www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment

nor to provide every possible contingency to meet in connection with installation,

operation, or maintenance. Should further information be desired or should

particular problems arise which are not covered sufficiently for the purchaser's

or owner's purposes, this matter should be referred to Acuity Brands Lighting,

Inc.

WARNING

RISK OF ELECTRIC SHOCK

► Disconnect or turn off power before installation or servicing.

► Verify that supply voltage is correct by comparing it with the luminaire label

information.

► Make all electrical and grounded connections in accordance with the National

Electrical Code (NEC) and any applicable local code requirements.

► All wiring connections should be capped with UL approved wire connectors.

CAUTION

RISK OF INJURY

► Wear gloves and safety glasses at all times when removing luminaire from

carton, installing, servicing or performing maintenance.

► Avoid direct eye exposure to the light source while it is on.

WARNING

RISK OF BURN

► Allow lamp/fixture to cool before handling. Do not touch enclosure, lens or light

source.

► Do not exceed maximum wattage marked on luminaire label.

► Follow all manufacturer's warnings, recommendations and restrictions including

but not limited to: driver type, burning position, mounting locations/methods,

replacement and recycling.

CAUTION

RISK OF FIRE

► Keep combustible and other materials that can burn, away from lamp/lens.

► Do not operate in close proximity to persons, combustible materials or substances

affected by heat.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF PRODUCT DAMAGE

► Never connect components under load.

► Do not mount or support these fixtures in a manner that can cut the outer jacket

or damage wire insulation.

► Controls for dimming, auto-sensing, or remote control of a luminaire that are

not factory-wired to the luminaire must be checked for compatibility with the

luminaire prior to installation. LED fixtures must be powered directly off a

switched circuit.

► Unless individual product specifications deem otherwise: Do not restrict fixture

ventilation. Allow for some volume of airspace around the fixture. Avoid

covering LED fixtures with insulation, foam, or other material that will prevent

convection or cooling.

► Unless individual product specifications deem otherwise: Do not exceed fixtures

maximum ambient temperature.

► Only use fixture in its intended location.

► LED products are Polarity Sensitive. Ensure proper Polarity before installation.

► Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal

grounding equipment must be worn during all installation or servicing of unit.

► Do not touch individual electrical components as this can cause ESD, shorten

lamp life, or alter performance.

► Some components inside the fixture may not be serviceable. In the unlikely

event your unit may require service, stop using the unit immediately and contact

an ABL representative for assistance.

► Changes or modifications not expressly approved by Acuity Brand Lighting

could void the authority to operate the equipment.

► Always read the fixtures complete installation instructions prior to installation

for any additional fixture specific warnings.

► Always ensure that the electrical distribution system is up to NEC (and applicable

local code) requirements.

► Verify that power distribution system has proper grounding. Lack of proper earth

ground can lead to fixture failure and may void warranty.

All luminaires that contain electronic devices that generate frequencies above 9kHz

from any component within the luminaire comply with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that

may cause undesired operation.

This device complies with Part 15 of the FCC Rules but may cause interference

with cordless and cell phones, radios, televisions, and other electronic devises.

To correct the problem, move the device away from the luminaire or plug into a

different outlet. This product may cause interference to radio equipment and should

not be installed near maritime safety communication equipment or other critical

navigation or communications equipment operation between. 0.45-30MHz.

5-YEAR LIMITED WARRANTY

prompt product registration confirms your right to the protection available under

the terms and conditions of your Lithonia Lighting warranty.

Failure to follow any of these instructions could void product warranties. For a

complete listing of product Terms and Conditions, please visit www.acuitybrands.

com. Acuity Brands Lighting, Inc. assumes no responsibilities for claims arising

out of improper or careless installation or handling of its products.

page 2