Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE Manuale di istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Luce per esterni Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE. Acuity Brands Lithonia Lighting TWR1 LED ALO SWW2 PE 8. Led wall pack
Stampa la paginaFIXTURE PARTS LIST
Description
1) Rear Housing ................................................................................................1
2) Door Assembly .............................................................................................1
3) 3/4" 1/4-20 Screws .......................................................................................2
4) Photocontrol switch ......................................................................................1
5) Lumen and color temperature
Lumen and color temperature .......................................................................1
6) Wire Nuts*
Wire Nuts* ....................................................................................................3
*Contained in parts packs
This wall pack is designed to be mounted to a recessed junction box and
directly to a flat wall for use with surface conduit.
CAUTION: DO NOT MOUNT WITH LIGHT AIMING UP, TO AN
EXTERNAL JUNCTION BOX, OR OVER RAISED RIBS AS FOUND IN
CORRUGATED SIDING
Remove fixture components and parts pack. Check to ensure all parts are
included. Note: Account for small parts and destroy packing material, as these
may be hazardous to children.
Turn OFF Power at circuit breaker box.
CAUTION: Do not rely on wall switch alone to turn off power
Switchable Photocontrol
Color Temperature
Adjustable Lumens
*Factory Setting
1. Remove the door assembly (2) from rear housing. Loosen two screws (3)
on the front Note: Do not remove screws completely. Open door, unplug orange
connector to disconnect LED wires and separate door assembly from rear housing.
2. Prepare the rear housing for installation by removing the knockout holes as
needed.
For junction box mounting, thread house supply wires through the center hole in
rear housing and secure the rear housing to junction box and wall.
For conduit mounting secure the rear housing to wall in appropriate method
and connect the liquid-tight conduit fitting to any of the 1/2" conduit entry holes.
Note: See FIGURE on last page for Mounting hole locations. Note: Assure that
fixture is mounted onto a structurally sound surface and use mounting hardware
appropriate for your application.
CAUTION: WIRING AND FIXTURE OPERATION
Make sure power is turned off.
3. Ground fixture using wire nut to connect the (copper or green) supply ground
wire & the green fixture ground wire. Note: If wiring does not include a ground
wire, consult your local electrical code for approved grounding methods.
For proper connection, place wire nut over wires
and twist clockwise until tight.
4. Connect supply wires using wire nut to connect the black fixture wire to the
black power supply wire and the white fixture wire to the white (neutral) supply
wire.
5. Luminaire is preset to highest lumens, 4000K CCT, and PE in the On position.
If desired, change settings by adjusting the switch. See Figure B
6. Reconnect door assembly to rear housing and re-connect LED wires with
orange connector. Close Door and tighten screws to 15-20 in-lbs. Do not
over-tighten the screws. Note: make sure no wires are pinched before tightening
screws.
7. Turn on electricity at fuse or circuit breaker box and verify success of
installation.
For Wet Location compliance, fixture must be properly sealed! Apply
caulking to the perimeter of the fixture between the housing and the wall (top and
two sides) leaving the bottom side clear of any caulking. Caulking will prevent
any water coming down the wall from entering the fixture. Note: Do not apply
caulking on the bottom.
Make sure all wiring access holes are sealed with weatherproof silicone
sealant (not included)!
Quantity
TWR1
TWR2
ON*/OFF
3000K/4000K*/5000K
8,000*
16,000*
5,000
12,000
2,000
8,000
INSTALLATION INSTRUCTIONS
4) Photocontrol
1) Rear housing
4) Photocontrol Switch
Photocontrol switch
page 3
2) Door Assembly
5) ALO/CCT Switch
SUPPLY HOT WIRE (BLACK)
/ CABLE CALIENTE (NEGRO)
/ FIL DE PHASE (NOIR)
SUPPLY NEUTRAL WIRE (WHITE)
/ CABLE NEUTRO (BLANCO)
/ FIL DE NEUTRE (BLANC)
SUPPLY GROUND WIRE
/ CABLE DE PUESTA A TIERRA
/ FIL DE TERRE
Figure B
Lumen switch
Color temperature switch
3) Screws
Figure A