DiMarzio angel dp232 Istruzioni per l'installazione - Pagina 3
Sfoglia online o scarica il pdf Istruzioni per l'installazione per Strumento musicale DiMarzio angel dp232. DiMarzio angel dp232 4.
Stampa la pagina1388 Richmond Terrace • PO Box 100387
Staten Island, NY 10310
www.dimarzio.com
FIG. 8
⁄ - inch (11.9 mm) hole
15
in guitar tail block
FIG. 9
FIG. 10
Volume Control locations
underneath soundhole
INSTALLATION INSTRUCTIONS − page 3
There should still be one locking washer, one at washer, and two hex nuts remaining on the
jack.
Using care to keep the washers on the jack, bring the preamp down through the soundhole
into the body and insert it into the hole in the tail block.
Adjust the internal nut so that the larger threaded section of the jack remains recessed
inch (0.8 mm) below the outside surface of the instrument and most of the smaller
threaded section protrudes from the guitar. The nut on the jack closest to the preamp is
factory installed and must not be adjusted. Adjusting this nut can damage the preamp.
With the preamp in place, lay the remaining at washer over the threads outside the
instrument and install the external hex nut hand tight.
Insert the included ⁄ - inch Allen wrench through the cross hole in the jack and hold rmly
while tightening the nut with a wrench. To avoid damage, do not hold the preamp itself
while tightening the nut. Use of a proper wrench instead of pliers will help prevent damage
to the guitar. To avoid cracking the guitar nish, do not over-tighten the nut.
NOTE: If the jack will not tighten firmly, remove the external hex nut and re-adjust the
internal hex nut until the larger threaded section is recessed at least ⁄ - inch (0.8 mm)
below the outer surface of the instrument.
Finish by installing the strap nut hand tight. It should cover the retaining nut and washer. For
best results, the end of the jack should be recessed ever so slightly from the end of the strap
nut.
Battery
Pouch
Once the preamp is installed, install two of the self-adhesive cable retainer clips on the inner
back surface of the guitar to hold down the pickup cable and prevent it from vibrating
against the guitar.
BATTERY POUCH INSTALLATION
The battery pouch will be installed on the at surface of the neck block or the side of the
guitar adjacent to the neck block as shown in FIG. 9. Clean the area where you will mount
the pouch using the included alcohol wipe or a cotton swab moistened with rubbing
alcohol. Let dry. Separate the battery pouch from the Velcro patch. Peel off the paper liner
from the Velcro patch and attach the patch to the chosen location. To set the adhesive,
press rmly on the entire area of the patch with your ngertip, especially around the edges.
Attach the battery clip to a 9V alkaline or lithium battery, install the battery into the pouch,
and re-attach it to the Velcro patch. Install one of the self-adhesive cable retainer clips on the
inner back surface of the guitar to hold down the battery cable and prevent it from vibrating
against the guitar.
NOTE: The adhesive under the Velcro patch requires 24 hours to achieve a full bond, so
take care not to stress the adhesive if you remove the battery pouch less than one day
after the initial installation.
VOLUME CONTROL INSTALLATION
Locate two at areas on the underside of the soundhole where the volume controls will t.
Clean the area where you will mount the controls using the included alcohol wipe or a
cotton swab moistened with rubbing alcohol. Let dry. Install each volume control by peeling
off the paper liner on the smooth side of the circuit board and pressing it rmly inside the
soundhole as shown in FIGURE 10. The Nano ex volume control cable is red, and The Angel
™ volume control cable is black. The volume controls should protrude from the sound hole
just far enough to be easily adjusted, as shown. Install one of the self-adhesive cable retainer
clips on the inner back surface of the guitar to hold down each volume control cable and
prevent it from vibrating against the guitar.
THE ANGEL™ SYSTEM DP232
⁄
1