Epson 755c - PowerLite XGA LCD Projector Manuale delle parti - Pagina 14

Sfoglia online o scarica il pdf Manuale delle parti per Software Epson 755c - PowerLite XGA LCD Projector. Epson 755c - PowerLite XGA LCD Projector 26. Release of check tool for network projectors v1.00 for windows
Anche per Epson 755c - PowerLite XGA LCD Projector: Manuale d'uso (42 pagine), Manuale operativo (36 pagine), Scheda tecnica (2 pagine), Manuale operativo (47 pagine), Bollettino di assistenza prodotti (30 pagine), Elementi sostituibili dall'utente (1 pagine), Impostazione rapida (2 pagine), Manuale di installazione (19 pagine), Manuale d'uso (1 pagine), Manuale delle funzioni (5 pagine), Bollettino di assistenza prodotti (25 pagine), Bollettino di assistenza prodotti (38 pagine), Bollettino di assistenza prodotti (12 pagine), Bollettino di assistenza prodotti (42 pagine), Bollettino di assistenza prodotti (22 pagine), Bollettino di assistenza prodotti (28 pagine), Bollettino di assistenza prodotti (41 pagine), Bollettino di assistenza prodotti (34 pagine), Bollettino di assistenza prodotti (38 pagine), Bollettino di assistenza prodotti (28 pagine), Bollettino di assistenza prodotti (15 pagine), Bollettino di assistenza prodotti (22 pagine)

Stampa la pagina
Epson 755c - PowerLite XGA LCD Projector Manuale delle parti
Epson PowerLite 755c/765c Projector
Access point mode: On the General tab, select
, then click the
Protocol
screen:
9. If your access point uses DHCP, select
. Otherwise, select
automatically
and enter the required information.
address
: Type in the IP address you want to assign to
IP address
the computer. It must be formatted like other addresses
on the network; usually the first three sections
(XXX.XXX.XXX) match the access point's IP address,
and the last section is unique.
: For example, 255.255.255.000, but this
Subnet mask
too must match how your network is set up.
: Enter the IP address that was assigned
Default gateway
to the access point when it was set up.
10.When done, click
.
OK
11.Click the
Wireless Networks
14
Epson PowerLite 755c/765c Projector
-
Internet
button. You see this
Properties
Obtain IP address
Use the following IP
tab. You see this screen:
Note:
If you don't see this tab, you may need to enable your wireless
card or network device by clicking
device settings; then follow any instructions on the screen to
enable the device.
12.Verify that you've enabled your computer's connection to
the access point. It should be listed as shown above, with the
small icon
next to it, indicating a connection.
If it's not listed, click
your access point.
13.When you're done, click
Wirelessly" on page 15.
Checking the Gateway (Access Point's) IP Address
If you're entering IP addresses manually in access point mode
and need to find out the gateway IP address (the IP address of
your access point), make sure the wireless connection to the
access point is currently active, as described in the previous
section.
Note:
If you can't identify the gateway address using this Windows utility,
use the administrator's utility software that came with your access
point.
1. Access your wireless network Properties window. For
example, in Windows XP click
Network and Internet Connections
double-click the
Network Connections
2. Right-click the
Wireless Network Connection
select
. Then click the
Status
The gateway's (access point's) IP address is listed as shown:
8/05
to access the
Configure
and then type the name of
Configure
. Continue with "Projecting
OK
Start > Control Panel >
. Then
icon.
tab.
Support
Gateway
address
icon and