Epson 755c - PowerLite XGA LCD Projector Parça Kılavuzu - Sayfa 14

Yazılım Epson 755c - PowerLite XGA LCD Projector için çevrimiçi göz atın veya pdf Parça Kılavuzu indirin. Epson 755c - PowerLite XGA LCD Projector 26 sayfaları. Release of check tool for network projectors v1.00 for windows
Ayrıca Epson 755c - PowerLite XGA LCD Projector için: Kullanıcı Kılavuzu (42 sayfalar), Kullanım Kılavuzu (36 sayfalar), Şartname Sayfası (2 sayfalar), Kullanım Kılavuzu (47 sayfalar), Ürün Destek Bülteni (30 sayfalar), Kullanıcı Tarafından Değiştirilebilir Öğeler (1 sayfalar), Hızlı Kurulum (2 sayfalar), Kurulum Kılavuzu (19 sayfalar), Kullanıcı Kılavuzu (1 sayfalar), İşlev Kılavuzu (5 sayfalar), Ürün Destek Bülteni (25 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (12 sayfalar), Ürün Destek Bülteni (42 sayfalar), Ürün Destek Bülteni (22 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (41 sayfalar), Ürün Destek Bülteni (34 sayfalar), Ürün Destek Bülteni (38 sayfalar), Ürün Destek Bülteni (28 sayfalar), Ürün Destek Bülteni (15 sayfalar), Ürün Destek Bülteni (22 sayfalar)

Sayfayı Yazdır
Epson 755c - PowerLite XGA LCD Projector Parça Kılavuzu
Epson PowerLite 755c/765c Projector
Access point mode: On the General tab, select
, then click the
Protocol
screen:
9. If your access point uses DHCP, select
. Otherwise, select
automatically
and enter the required information.
address
: Type in the IP address you want to assign to
IP address
the computer. It must be formatted like other addresses
on the network; usually the first three sections
(XXX.XXX.XXX) match the access point's IP address,
and the last section is unique.
: For example, 255.255.255.000, but this
Subnet mask
too must match how your network is set up.
: Enter the IP address that was assigned
Default gateway
to the access point when it was set up.
10.When done, click
.
OK
11.Click the
Wireless Networks
14
Epson PowerLite 755c/765c Projector
-
Internet
button. You see this
Properties
Obtain IP address
Use the following IP
tab. You see this screen:
Note:
If you don't see this tab, you may need to enable your wireless
card or network device by clicking
device settings; then follow any instructions on the screen to
enable the device.
12.Verify that you've enabled your computer's connection to
the access point. It should be listed as shown above, with the
small icon
next to it, indicating a connection.
If it's not listed, click
your access point.
13.When you're done, click
Wirelessly" on page 15.
Checking the Gateway (Access Point's) IP Address
If you're entering IP addresses manually in access point mode
and need to find out the gateway IP address (the IP address of
your access point), make sure the wireless connection to the
access point is currently active, as described in the previous
section.
Note:
If you can't identify the gateway address using this Windows utility,
use the administrator's utility software that came with your access
point.
1. Access your wireless network Properties window. For
example, in Windows XP click
Network and Internet Connections
double-click the
Network Connections
2. Right-click the
Wireless Network Connection
select
. Then click the
Status
The gateway's (access point's) IP address is listed as shown:
8/05
to access the
Configure
and then type the name of
Configure
. Continue with "Projecting
OK
Start > Control Panel >
. Then
icon.
tab.
Support
Gateway
address
icon and