Whirlpool 8527813 Manuale di istruzioni per l'installazione - Pagina 3

Sfoglia online o scarica il pdf Manuale di istruzioni per l'installazione per Asciugatrice Whirlpool 8527813. Whirlpool 8527813 13. Commercial stacked dryer gas & electric

Stampa la pagina

The collar houses the accumulator

timers with actuating arm and button.

The timers are set to provide 45

minutes (4 pins) of drying time when

activated by the coin slide. Timer

cams for 30-minute (6 pins) and 60-

minute (3 pins) drying times are

included in the parts bag.

The coin-slide mechanism, control

panel lock and key, and coin-box lock

and key are not included and are

available from usual industry sources.

To change to a

30- or 60-minute

timingcam

WARNING

Electrical Shock Hazard

Disconnect power before

servicing.

Replace all parts and panels

before operating.

Failure to do so can result in

death or electrical shock.

Each coin-operated dryer is

equipped with a 45-minute timer

cam that provides 45 minutes of

drying time when activated by the

coin slide.

You can install the 30-minute or

60-minute timing cam (shipped with

dryer) as follows:

1. Unlock control panel. Lift up and

rotate out from cabinet. Control

panel will still be attached to

cabinet.

2. Reach into control panel area.

Use Phillips screwdriver to loosen

(but not remove) timer mounting

bracket screw. Lift up to remove

timer assembly and bracket from

cabinet.

ratchet tooth

timing cam

3. Turn the timing cam by hand until

the "V"-shaped notch lines up

below the ratchet tooth.

timing cam

ratchet tooth

Line up

notch to

clear

hub

ratchet

down

tooth.

4. Insert a narrow, flat-blade

screwdriver under the timing cam

near the clock shaft. Gently lift cam

straight up and off shaft making

sure that the "V" -shaped notch

clears the ratchet tooth.

5. Place new cam (hub side down)

over clock shaft. Line up flat side of

shaft with flat side of cam hole.

Check that drive lug is in place.

6. Turn cam until "V" -shaped notch

lines up with ratchet tooth.

7. Press cam down in place on motor

shaft. Make sure that "V" -shaped

notch clears the ratchet tooth.

8. Reattach the timer bracket

assembly; then tighten the screws.

9. Repeat steps for other timer.

10. Close and lock the control panel..

Exhaust

requirements

WARNING

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to do so can result in

death or fire.

Do not use non-metal flexible vent,

metal vent that is smaller than four

inches in diameter or exhaust hoods

with magnetic latches.

The dryer must be exhausted outdoors.

Do not exhaust dryer into a gas vent,

chimney, wall, ceiling, or concealed

space of a building.

Do not install flexible vent in enclosed

walls, ceilings or floors.

If using an existing exhaust system,

clean lint from entire length of exhaust

system. Make sure exhaust hood is not

plugged with lint.

The exhaust system should be

inspected and cleaned yearly.

Replace any plastic or metal foil

exhaust vent with rigid metal or

flexible metal vent.

drive

lug

Use 4" (10.2 cm) vent clamps to

secure vent system.

better

exhaust

airflow

Four-inch (10.2 cm) metal exhaust vent

is required. Plan installation to use the

fewest number of elbows and turns.

Metal flexible vent must be fully

extended and supported when the

dryer is in its final position. DO NOT

KINK OR CRUSH THE VENT. The metal

flexible vent must be completely

open to allow adequate exhaust air

to flow.

Allow as much room as possible

when using elbows or making turns.

Bend vent gradually to avoid kinking.

Remove excess flexible vent to avoid

sagging and kinking that may result in

reduced air flow.

Exhaust outlet is located at the

center of the bottom dryer back.

The exhaust vent can be routed up,

down, left, right, behind the dryer or

straight out the back of the dryer.

Maximum length of exhaust system

depends upon the type of vent used,

number of elbows and type of

exhaust hood. The maximum length

for both rigid and flexible vent is

shown in the chart.

(10.2 cm)

No.

of 90°

turns

(10.2 cm)

MAXIMUM LENGTH OF 4-INCH (10.2 cm) DIAMETER

exhaust airflow

good

exhaust

airflow

EXHAUST HOOD TYPE

(10.2 cm)

2-1/2"

(10.2 cm)

(6.4 cm)

RIGID METAL VENT

64 FT. (19.5 m)

58 FT. (17.7 m)

54 FT. (16.5 m)

48 FT. (14.6 m)

38 FT. (11.6 m)

44 FT. (13.4 m)

29 FT. (8.8 m)

35 FT. (10.7 m)

21 FT. (6.4 m)

27 FT. (8.2 m)

FLEXIBLE METAL VENT

28 FT. (8.5 m)

36 FT. (11.0 m)

31 FT. (9.4 m)

23 FT. (7.0 m)

19 FT. (5.8 m)

27 FT. (8.2 m)

17 FT. (5.2 m)

25 FT. (7.6 m)

15 FT. (4.6 m)

23 FT. (7.0 m)

Page 3