Whirlpool CGW9100VQ0 Manuale di installazione - Pagina 11

Sfoglia online o scarica il pdf Manuale di installazione per Asciugatrice Whirlpool CGW9100VQ0. Whirlpool CGW9100VQ0 40. Commercial dryer- gas or electric

Stampa la pagina

[]

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 200 CFM of air per

dryer. Large-capacity

lint screens of proper design may be

used in the main vent if checked and cleaned frequently. The

room where the dryers are located should have make-up air

equal to or greater than the CFM of all the dryers in the room.

[]

Back-draft Damper Kit, Whirlpool Part No. 3391910, is

available from your dealer and should be installed in the vent

of each dryer to prevent exhausted air from returning into the

dryers and to keep the exhaust in balance within the main

vent. Unobstructed

air openings are required.

Each vent should enter the main vent at an angle pointing in the

direction of the airflow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30 °.

air flow

_---

A. Individualdryervent

B. Mainvent

Keep air openings free of dry cleaning fluid fumes. Fumes create

acids which, when drawn through the dryer heating units, can

damage dryers and loads being dried.

A clean-out cover should be located on the main vent for periodic

cleaning of the vent system

If an exhaust hood cannot be used:

................

G.Roof

2 ft. (61 cm) min.

above highest

point of building

The outside end of the main vent should have a sweep elbow

directed downward. If the main vent travels vertically through the

roof, rather than through the walt, install a 180° sweep elbow on

the end of the vent at least 2 ft. (61 cm) above the highest part of

the building. The opening in the wall or roof shall have a diameter

1Z2" ( 1.3 cm) larger than the vent diameter. The vent should be

centered in the opening.

Do not install screening or cap over the end of the vent.

INSTALLATION INSTRUCTIONS - COINSLIDEANDCOINBOX

The console houses the factory-installed

accumulator

timer with

actuating arm and button.

The factory-installed

timer is set to provide 45 minutes (4 pins)

of drying time when activated by the coin slide. Timer cams for

30-minute (6 pins) and 60-minute (3 pins) drying times are

included in the parts bag.

The coin slide mechanism, control panel lock and key, and coin

box lock and key are not included and are available from usual

industry sources.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

NOTE: Slide dryer onto cardboard or hardboard before moving to

avoid damaging floor covering.

1. Using two or more people, move dryer to desired installation

location.

2. Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe the interior of the

drum thoroughly with a damp cloth.

Take two of the cardboard corners from the carton and place

them on the floor in back of the dryer. Firmly grasp the body

of the dryer and gently lay it on its back on the cardboard

corners.

With one of the legs in hand, check the ridges for a diamond

marking. That's how far the leg is supposed to go into the

hole.

Start to screw the leveling legs into the holes by hand. (Use a

small amount of liquid detergent to lubricate the screw

threads so it is easier to turn the legs.) Use a 1" wrench or

socket wrench to finish turning the legs until you reach the

diamond mark.

Now stand the dryer up.

Remove the service

door of the meter case

by lifting it up at the

back. Install the money-

accepting device. (Refer

to manufacturer's

instructions for proper

installation.)

For dryers using coin

slides, use the adapter kit supplied with the dryer.

Replace the meter case service door. Put the coin vault with

lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer.the legs of

the dryer up or down until the dryer is level.