Whirlpool RANGE HOOD UXT2036AY Istruzioni per l'installazione e manuale d'uso e manutenzione - Pagina 10
Sfoglia online o scarica il pdf Istruzioni per l'installazione e manuale d'uso e manutenzione per Cappa di ventilazione Whirlpool RANGE HOOD UXT2036AY. Whirlpool RANGE HOOD UXT2036AY 36. 30" (76.2 cm) and 36" (91.4 cm)
Anche per Whirlpool RANGE HOOD UXT2036AY: Istruzioni per l'installazione e manuale d'uso e manutenzione (28 pagine), Istruzioni per l'installazione e manuale d'uso e manutenzione (28 pagine)
Stampa la pagina
1.
2.
3.
,,
a ¸ ,,
_
,
_,,_S_3 _{?_,_,_ _{_s_ _
Lift the range hood up under cabinet and determine final
&
location by centering beneath cabinet. Mark on the underside
of cabinet the location of the 4 keyhole mounting slots on the
range hood. Set range hood aside on a covered surface.
A
\
A. Keyhole slot
Use V8" (3 mm) drill bit and drill 4 pilot holes as shown.
A
A. Drill pilot hole
Install the 4 - 4.5 mm x 13 mm mounting screws in pilot
holes. Leave about V4" (6.4 cm) space between screw heads
and cabinet to slide range hood into place.
6.
Remove metal grease filters. See the "Range Hood Care"
section.
NOTE: Depending on your model, you will have either a
7" (17.8 cm) round vent mounting plate or 3-1/4" x 10"
(8.3 x 25.4 cm) rectangular vent connector on the inside your
range hood. Some models are recirculation (non-vented only)
and will not have a vent damper.
Remove the 7" (17.8 cm) round vent mounting plate and the
3-1/4" x 10" (8.3 x 25.4 cm) rectangular vent connector
attached with screws or taped on the inside your range hood.
1i4uu
(6.4 ram)
4. Remove damper knockouts depending on your model.
C
A. Round vent knockout
B. Top rectangular vent knockout
C. Rear rectangular
vent knockout
Round vent system installations - Remove top rectangular
and round vent knockouts.
Rectangular vent system installations - For roof
installations,
remove the top rectangular vent knockout.
For
wall installations, remove the rear rectangular vent knockout.
Non-vent
(recirculating)
installations
- Do not remove any
knockouts.
7,
B
A. 7" (17.8 cm) round vent mounting plate
B. Screws
C. 3 _" X 10" (8.3 X24.4 cm) rectangular
vent connector
Install 7" (17.8 cm) round vent mounting plate or 3-1/4" x 10"
(8.3 x 25.4 cm) vent connector, depending
on your vent
system installation. Attach to range hood 6.5 x 9.5mm screws
provided and remove tape from damper flap.
NOTE: On some models, the 7" (17.8 cm) round vent
mounting plate is not supplied. An optional 7" (17.8 cm)
round damper is also available as an accessory. For
information
on ordering, see the "Accessories"
section.
!
_A
B
D
E
A. 7" (17.8 cm) Round damper (see "Accessories"
section)
B. Sheet metal screws
C. 7" (17.8 cm) round vent mounting plate
D. Round vent knockout
E. Rectangular vent knockout
10