Alemite 8700 Manuale di servizio - Pagina 5

Sfoglia online o scarica il pdf Manuale di servizio per Pompa dell'acqua Alemite 8700. Alemite 8700 9. High-pressure hydraulic pump

Stampa la pagina

SER 8700

IMPORTANT: Prior to performing any main-

tenance procedure, the following safety pre-

cautions must be observed. Personal injury

may occur.

WARNING

Do not use halogenated hydrocarbon solvents

such as methylene chloride or 1,1,1-trichloroethane in

this pump. An explosion can result within an enclosed

device capable of containing pressure when aluminum

and/or zinc-plated parts in the pump come in contact

with halogenated hydrocarbon solvents.

Release all pressure within the system prior to perform-

ing any overhaul procedure.

•

Disconnect the hydraulic supply line from the pump

motor.

•

Into an appropriate contai n er, operate the control

valve to discharge remaining pressure within the

system.

Never point a control valve at any portion of your body or

another person. Accidental discharge of pressure and/or

material can result in injury.

Read each step of the instructions carefully. Make sure a

proper understanding is achieved before proceeding.

Overhaul

NOTE: Refer to Figure 2 for component

identification on all overhaul procedures.

Disassembly

1. Secure the pump assembly in a soft-jaw vise at Adapter

(3).

2. Extend Primer Rod (27) to end of Primer Body (33).

3. Gently remove Nut (30) from the Primer Rod.

• Use an appropriate size punch in the hole of the

Primer Rod to prevent rotation. See Figure 2.

4. Remove Primer Disc (29) from the Primer Rod.

5. Push the Primer Rod into the Primer Body.

Pump Tube (Outer Components)

6. Rotate the Primer Body.

• Use a large wrench or other suitable tool.

Revision (2-13)

NOTE: The pump tube will break at one of

three places. Unscrew the separated portion

from the inner components of the pump tube

assembly.

7. Remove Follower Tube (31) [assembly] from the inner

tube assembly.

8. Unscrew the hydraulic motor from Adapter (3).

• Rotate the hydraulic motor assembly.

9. Remove O-Ring (2) from the Adapter.

NOTE: If the pump was not leaking at the

top of Tube (16), do not separate the Adapter

from the Tube. Components are locked with

™

Loctite 222. Unscrew Tube (16) from the

Adapter as required.

• Remove Gasket (4).

10. Clamp Retainer (18) horizontally in a soft-jaw vise.

11. Unscrew the Primer Body from Extension (22).

12. Remove O-Ring (32) from the Primer Body.

I MPOR TANT: Remove Valve Seat (26)

squarely from the Primer Body. Should the

Valve Seat cock during removal, realign and

start again. Gasket (4) may interfere.

13. Remove Valve Seat (26) from the Primer Body.

14. Remove Gasket (4) from the Valve Seat.

15. Unscrew the Extension from the Retainer.

16. Remove Gasket (21) from the Extension.

17. Remove Valve Body (25) from the Extension.

• Remove Stop Washer (23).

18. Remove Seal (24) from the Valve Body.

19. Remove Bearing (20) and Seal (19) from the Retainer.

20. Unscrew Tube (16) from the Retainer.

21. Remove Gasket (4), Bearing (17), and additional

Gasket (4) from the Retainer.

Pump Tube (Inner Components)

22. Remove Pin (6) that secures Coupling (5) to the

hydraulic motor rod.

• Unscrew the Coupling assembly from the hydraulic

motor rod.

High-Pressure Hydraulic Pump

Alemite LLC