- ページ 4

母乳ポンプ Ameda EliteのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Ameda Elite 13 ページ。 Electric breast pump
Ameda Elite にも：取扱説明書 (2 ページ), クイック・スタート・マニュアル (2 ページ), 取扱説明書 (10 ページ)

ページを印刷する

1. Maintenance

Set Up and Assembly

Ameda HygieniKit Milk Collection System

Before Every Use

Always wash hands well with soap and water before

handling the Ameda Elite Breast Pump and Ameda

HygieniKit Milk Collection System.

IMPORTANT NOTE: ONLY USE THE AMEDA HYGIENIKIT

MILK COLLECTION SYSTEM ON AMEDA ELECTRIC BREAST

PUMPS.

Prior to starting pump, assemble and connect the Ameda

HygieniKit Milk Collection System, per included instructions. If

the Ameda HygieniKit Milk Collection System is sterile, use as

is. If not sterile, see the Ameda HygieniKit Milk Collection

System cleaning instructions.

Adapter Cap

Silicone Diaphragm

Breast Flange

Valve

Milk Bottle

Tubing

Tubing Adapter

The Ameda HygieniKit Milk Collection System can be used

to single or dual pump.

To dual pump:

To single pump:

Remove one tube and

Both tubes should be

close tubing adapter.

attached to tubing

adapter.

Elite with Detachable Power

Cord

• Attach Ameda supplied

power cord to AC power

inlet on rear of pump.

• Connect power cord to wall

outlet.

Elite with Built-in Power

Cord

• Connect power cord to wall

outlet.

E N G L I S H

• Insert tubing adapter into

tubing adapter port on

piston/cylinder.

Operating the Pump

• Center nipple(s) in breast

flange(s) and fill breast

flange(s) with the breast(s)

to create an air seal.

• Turn the pump ON by turning

the 'VACUUM' dial to the

right.

Setting Suction

• Increase the suction by

turning the 'VACUUM' dial to

the right. Increase suction

until reaching maximum

comfort level.

• If discomfort is felt in nipple(s)

or breast(s), decrease suction.

If discomfort is felt at all

suction settings, turn pump

off, insert a finger between breast(s) and breast flange(s)

to break suction, remove breast flange(s) from breast(s).

Discontinue pumping and contact a healthcare provider.

Setting Speed

• Start with the 'CYCLES' dial

all the way to the right to

increase the speed and

trigger a milk ejection reflex

(let-down)

• When milk flows, (let-down)

turn the 'CYCLES' dial to the

left to slow down the speed

to help drain the breast

faster. When milk flow slows, turn the 'CYCLES' dial all the

way to the right to help start another (let-down). Repeat as

milk flow changes to pump more milk.

Turning Pump OFF

• When finished pumping, turn

the 'VACUUM' dial all the

way to the left to turn the

pump off.

Removing Ameda HygieniKit Milk Collection System

from Breast(s)

• After pump is switched off, if necessary, insert a finger

between breast(s) and breast flange(s) to break suction.

• Remove breast flange(s) from breast(s).

Cleaning the Ameda Elite Breast Pump

• Disconnect the pump

power cord from wall

outlet.

• Remove piston cylinder by

placing index finger into the

tube, lifting upwards and

turning right to release

from attachment bars.

For At-Home/End-Users

After each pumping, wipe

pump with cloth dampened

with warm, soapy water.

For Hospitals/Rental Stations

Clean between users.

Spray with recommended

disinfectant, such as

CaviCide

. Wipe with soft

cloth. Do not use products

containing phenol.

Do not use bleach on pump.

• Place piston cylinder back

onto attachment bars and

press gently into place with

thumb.

Troubleshooting

Pump Does Not Turn ON

• Ensure proper power cord connection to pump.

• Ensure power cord connection to wall outlet.

• Ensure outlet has power.

Low or No Suction

• Check breast flange for adequate seal against breast.

• Check that the Ameda HygieniKit Milk Collection System

is properly assembled.

• Check that adapter cap is firmly snapped onto top of

breast flange.

• Ensure silicone diaphragm is in place inside top of breast

flange.

• Ensure tubing adapter is properly fitted into tubing

adapter port on pump.

• Inspect valve for stretching or tears. If seen, replace

valve.

• Ensure valve is pushed firmly into place in lower portion

of breast flange.

• Ensure one side of tubing adapter is closed when single

pumping.

Maintenance

It is recommended the Ameda Elite Breast Pump be

inspected at least once every year to include the following:

• Visually check pump housing for cracks, breakage, or

damage and ensure pump feet are present.

• Visually check for power cord damage.

• Check for proper operation of controls and buttons.

• Check there are no missing screws.

• Check tubing adapter port on piston/cylinder is free from

obstruction.

Quick Functional Check

The following checks/tests should be performed prior to use

by a new user:

• Visual checks for power cord damage.

• Check for abnormal noise.

• Check for proper operation of controls.

Replacing Detachable Power Cord (if applicable)

• Power cord is detachable from power inlet.

• If power cord condition is in doubt, only replace with

Ameda supplied 2 conductor cord.

Technical Information

Main voltage

Elite with Detachable Power Cord 100VAC to 240VAC

Elite with Built-In Power Cord 100/120V ~ or 220/240V ~ /AC

Frequency

50 / 60 Hz

Power consumption

30 VA

Main fuse

T 1.6A

Protection class

Class II

Double isolated

Safety level

= BF

Drip protection

IP 21

Operational conditions +10 - +40°C

10 - 90% rel. humidity

Transport and

- 40 - +70°C

Storage conditions

10 -100% rel. humidity

Weight

6.4 lbs/2.9 kg

Dimensions

10.0"L x 9.0"W x 7.5"H

22.2cmL x 26.7cmW x 18.4cmH

Vacuum max.

[mbar]

[mm Hg]

Single HygieniKit

350 ( -10% )

262 ( -10% )

Dual HygieniKit

310 ( -15% )

232 ( -15% )

Variable cycle

30 - 60 / Min

Conforming to

0086

E325189 MEDICAL EQUIPMENT

WITH RESPECT TO ELECTRIC SHOCK,

FIRE AND MECHANICAL HAZARDS ONLY.

IN ACCORDANCE WITH

IEC60601-1: 1988 + A1:1991 + A2:1995,

IEC60601-1-2, CAN/CSA C22.2 No. 601.1-M90

Evenflo Company, Inc.

1801 Commerce Drive

Piqua, Ohio 45356

USA

EMERGO EUROPE

Molenstraat 15

2513 BH, The Hague

The Netherlands

Phone: +31.70.345.8570

Fax:

+31.70.346.7299

E N G L I S H