- ページ 16

トレッドミル Domyos TC 140のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Domyos TC 140 18 ページ。
Domyos TC 140 にも：取扱説明書 (18 ページ), 取扱説明書 (18 ページ), 取扱説明書 (18 ページ), 取扱説明書 (18 ページ), 取扱説明書 (18 ページ), 取扱説明書 (18 ページ)

ページを印刷する

TC140GB.QXD

30/11/2004

If you notice noise from the moving treadmill increasing:

Turn it off at the main switch and remove the connector from the socket.

Raise the machine to put it carefully in a vertical position.

Use a rag to clean the inside of the mat whilst turning it manually to clean the entire surface. Return the machine to its

usual position. If the edges of the mat are damaged, check its alignment. If the stitching is ripped, please contact in

your Décathlon retailer.

Spray a silicon fluid (see a silicon spray manufacturer) onto the mat, an easy and quick operation.

Loosen the mat and spray the silicon both sides of it making sure to cover the entire surface.

DO NOT LOOSEN THE MAT THAT SPRAY FROM UNDERNEATH

Comment: Contact your Décathlon store for advice on an appropriate silicon liquid.

The electronic components and hardware regularly carry out an automatic self-

check procedure. If any errors are found, the console will display an error mes-

sage and will switch the treadmill off.

Error Message

Description

Speed error

1. When E1 appears, take the security key out and then reinsert to restart the

belt.

2. If the same E1 error message reappears after resetting, check all electric

connections. If the power cable is incorrectly connected, plug it in properly

and try again. If the cable is correctly plugged in, stop using the treadmill

and contact Customer Service.

Resetting error messages

To reset error messages, take the security key out and reinsert.

PROBLEM: The belt will not switch in

1 - Check that the belt's master switch is in position 1.

2 - Check that the power cord is connected at both ends (belt and mains sup-

ply).

3 - Take magnetic key out of the console. Reinsert the key into the console.

4 - Check that the mains socket is working (plug in a lamp, for example).

5 - Check the circuit breaker. If it has tripped, reset it (see instructions page 24).

6 - If you have carried out the above procedures and the problem continues to

occur, please contact customer service.

14:37

Page 26

TREADMILL LUBRICATING

T R O U B L E S H O O T I N G E R R O R M E S S A G E S

CARE

MOVING

Your treadmill is fitted with rollers for easy movement.

Before moving the machine, ensure the main switch to

is in position 0 and that the connector has been remo-

ved from the power.

Lift the treadmill chassis and move it as required.

Before moving the treadmill: check the raising piston is

locked before moving or putting it away.

Turn the treadmill forward to position it on the rollers.

Once it is in the design position, blocked it using your

foot and drop it until it is in complete contact with the

ground.

PROBLEM : The belt switches on but does not start running

1 - Check that the magnetic key is correctly inserted in the console.

2 - Ensure that you have pressed the START button.

3 - If you have carried out the above procedures and the problem continues to

occur, please contact customer service.

PROBLEM : The belt speed is not constant

1 - If you use an extension cord, remove it and try again.

2 - Check that the power cord is connected at both ends (belt and mains sup-

ply).

3 - Check that the running surface is not too tight or too loose (see instructions

page 25).

4 - If you have carried out the above procedures and the problem continues to

occur, please contact customer service.

PROBLEM: The belt displays an E1 error message

1 - Please refer to the instructions above.

2 - If necessary, please contact customer service.

PROBLEM: The belt makes a noise

1 - Check that your running belt is properly aligned (see instructions page 25).

2 - Check that your running belt is tight enough (see instructions page 25).

3 - Check that your running belt is clean (see instructions page 25).

4 - Check that the interior of the belt is sufficiently lubricated with silicon

(see instructions page 26).

5 - If you have carried out the above procedures and the problem continues to

occur, please contact customer service.