- ページ 2

ポータブル・ステレオ・システム eKids 430のPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。eKids 430 2 ページ。 Cd boombox
eKids 430 にも：クイック・スタート・マニュアル (15 ページ), マニュアル (2 ページ), クイック・スタート・マニュアル (12 ページ), クイック・スタート・マニュアル (5 ページ)

ページを印刷する

BASIC FUNCTION

SWITCHING ON THE UNIT

After connecting the power, press the

/SOURCE button to turn the unit ON or OFF.

NOTE: In CD/AUX/BLUETOOTH mode, when the unit is not providing the main

function for 15 minutes, the unit will automatically switch into standby mode. Press

the

/SOURCE button to turn on the unit again.

Please note that low volume setting in the audio source may be recognized as "no

audio signal", this will affect the capability of signal detection from the device and

can also originate an automatic switch into standby mode. If this happens please

reactivate the audio signal transmission or increase the volume setting on the audio

source player in order to resume playback.

Electrostatic Discharge hints - The unit may reset or may not reset to normal

operation mode due to electrostatic discharge, just switch it off and reconnect again.

ADJUSTING VOLUME

Press the VOL.+ or VOL.- button on unit to increase or decrease volume.

BLUETOOTH OPERATION

1. Press the

/SOURCE button on unit to select Bluetooth mode, the LCD will

display "bt".

2. Turn on the Bluetooth function on your device, and select "BT-430" to connect.

Input the password '0000' if required. The display will show "bt". Press

PLAY/PAUSE/REPEAT/PAIR button to start playback.

3. Press the VOL.+ or VOL.- button on unit or adjust the volume on the external

device to your desired level.

4. Press

on unit to choose the desired track.

5. To stop playback, press PLAY/PAUSE/REPEAT/PAIR button on unit.

6. Press and hold PLAY/PAUSE/REPEAT/PAIR button to disconnect Bluetooth.

Note: The Bluetooth works best within 10 meters in open air.

CD OPERATION

Discs for Playback

This system can playback all digital audio CD, finalized digital audio CD-Recordable

(CD-R) discs, finalized digital audio CD-Rewritable (CD-RW) discs.

LOADING A DISC

1. Press the

/SOURCE button on unit to select "CD" mode.

2. Push to open CD door, "OP" will be shown on the display.

3. Place an audio CD into the tray with the front side facing up.

4. Close the CD door, the display will show a flashing "- -", then the playback will

start from the first track.

5. To remove the CD, press STOP/PROG button to stop, then open the CD

compartment lid. Hold the CD by its edges, and take it out carefully.

Note:

1. Make sure the disc is stopped before opening the CD DOOR.

2. To ensure good system performance, wait until the unit completely reads the disc

before proceeding.

3. If no disc loaded into the tray, or the disc is unreadable, the display will show

"NO".

PLAYING A DISC

1. The playback starts from track 1, Press the PLAY/PAUSE/REPEAT/PAIR button

to pause playback, the ► indicator and the current track will flash on the display.

To resume playback, press the PLAY/PAUSE/REPEAT/PAIR button again.

2. To stop playback, press the STOP/PROG button, the total number of tracks

appears on the display.

SELECTING A DESIRED TRACK/PASSAGE

To select a desired track

Press the

button on unit while in stop mode, until the desired track

appears on the display. Then press the PLAY/PAUSE/REPEAT/PAIR button to play.

CONTROLS

11 12

1. HANDLE

10. SPEAKERS

2. CD COMPARTMENT

11. STB INDICATOR

3. NEXT/FAST FORWARD BUTTON

12. LCD DISPLAY

4. PREV/FAST BACKWARD BUTTON

13. BATTERY COMPARTMENT

5. VOL. - BUTTON

14. AC SOCKET

/SOURCE BUTTON

15. AUX-IN JACK

7. PLAY/PAUSE/REPEAT/PAIR BUTTON

16. MIC JACK

8. STOP/PROG BUTTON

17. MICROPHONE

9. VOL.+ BUTTON

To search for a particular passage during playback (track scanning at high speed)

Press and hold the

speed until desired point (passage) appears, then release the button for normal

playback mode. Playback w ill start again from this point.

PROGRAMMING TRACKS

Programming tracks is possible when playback is stopped. Up to 20 tracks of a CD

can be stored in the memory in any order.

1. In stop mode, press and hold the STOP/PROG button. The unit enters program

setting, the "PROGRAM" indicator will flash on the display and show P01.

2. Press the

(example: track 2)

3. Press and hold the STOP/PROG button on unit to enter. The display would flash

PROGRAM and show P02.

4. Repeat steps 2 & 3 to store other desired tracks until all tracks programmed.

5. Press the PLAY/PAUSE/REPEAT/PAIR button on unit to start playback from the

first programmed track.

6. Press the STOP/PROG button on unit to stop program playback. To clear the

program, you may press STOP/PROG button on unit when the disc stopped and

open the CD compartment lid, the program will be erased.

REPEAT PLAY

You can play one track or all tracks on the disc repeatedly.

To Repeat a Single Track

1. Press and hold PLAY/PAUSE/REPEAT/PAIR button during play, the display will

show a flash "REPEAT" indicator and the current track will be played over and over

again.

2. To cancel repeat play, press and hold the PLAY/PAUSE/REPEAT/PAIR button

repeatly until "REPEAT" disappears from the display.

To repeat all the Tracks

1. Press and hold PLAY/PAUSE/REPEAT/PAIR button while in Repeat Single Track

mode until the "REPEAT" indicator shows steadily on the display, all tracks on the

disc will be played over and over again.

2. To cancel repeat play, press and hold the PLAY/PAUSE/REPEAT/PAIR button

repeatly until "REPEAT" disappears from the display.

RANDOM PLAY

Press and hold the PLAY/PAUSE/REPEAT/PAIR button repeatly till the "RAN" shows

steadily on the display, the random play will start from next track automatically, until all

tracks are played over and then it will stop. To cancel, press and hold the

PLAY/PAUSE/REPEAT/PAIR button until the "RAN" disappears from the display.

AUX-IN OPERATION

1. Press the

/SOURCE button to select "AUX" mode.

2. Insert one end of a AUX line plug into the AUX IN jack (3.5mm) on the unit, and the

other end to the headphone jack of your music device to amplify music.

3. Control play/pause and navigate tracks using your music device.

4. Adjust the volume on the unit or on the device to your desired level.

MICROPHONE OPERATION

This unit provides one 3.5mm Mic Jack for Karaoke function. The microphone is

available in all modes. Connect a 3.5mm microphone to the mic jack, then turn on the

microphone.

button on unit to scan the current playing track at high

button to select the first desired track to be programmed.